Lennox Hearth Stove H8346 DRTRM GV230 NKL User Manual

HEARTH PRODUCTS  
KITS AND ACCESSORIES  
P/N 506033-57  
Rev. NC, 08/2011  
GRANDVIEW™ DOOR TRIM KIT  
INSTALLATION INSTRUCTIONS FOR INSTALLING DOOR TRIM  
ON A GRANDVIEW™ 230 WOODSTOVE  
Step 2. Gently pry back the door gasket, only where the screws are lo-  
cated (next to the identifying holes), and loosen the three bottom  
screws. NOTE* DO NOT REMOVE. An 1/8” allen wrench will be  
necessary. Once bottom three screws are loosened, completely  
remove remaining seven screws around the door.  
KIT CONTENTS  
Please ensure that all these parts are included  
1 ea. Door Trim  
1 ea. Instruction Sheet  
Grandview™ Door Trim Kit  
Cat. No.  
H8346  
H8347  
Model  
Description  
Door Trim, Nickel  
Door Trim, Brushed Nickel  
Glass  
Retainer  
DRTRM-GV230-NKL  
DRTRM-GV230-BRNKL  
Locate screws (10 ea.)  
(peal back gasket as shown)  
Door Gasket  
Arrows indicate  
screw locations  
TOOLS NEEDED  
1/8” Allen Wrench  
Flat Head Screwdriver  
Glass Cleaner/Soft Cloth  
Back View of Door  
Figure 1  
GENERAL INFORMATION  
Step 3. Separate the outer door from the inner door, by pulling apart at  
the top, creating the necessary gap to slide the door trim in place.  
If you encounter any problems, need clarification of these instructions or  
are not qualified to properly install this kit, contact you local distributor  
or dealer.  
Door Trim  
Outer Door  
Read this instruction sheet in its entirety before beginning the installa-  
tion.  
Glass Retainer  
ALL WARNINGS, PRECAUTIONS AND INSTRUCTIONS IN THE INSTAL-  
LATION AND OPERATION MANUAL PROVIDED WITH THE APPLIANCE  
APPLY TO THESE INSTRUCTIONS.  
Check the contents of the kits upon receipt and check for any damaged  
or missing parts. If there is hidden damage, notify your freight company  
or Lennox Hearth Products dealer immediately.  
Inner Door  
Be sure to clean plated surfaces with a soft cloth and household glass  
cleaner prior to burning the appliance. Fingerprints left on plated  
surfaces while burning may remain on the finish permanently.  
Hex Head  
Screws 10 ea.  
Glass with Gasket  
Figure 2  
Step 4. Slide door trim between inner and outer door, with desired finish  
facing outward. Ensure the notches on the door trim seat into,  
and are being captured by the mounting bosses on the outer  
door.  
Step 5. Once door trim is in place, re-install door screws and tighten  
all door screws snugly. Ensure rope is firmly placed back into  
channel.  
Step 6. Wipe down door trim with glass cleaner and soft cloth, as any  
fingerprints or dirt will remain permanently after stove is fired.  
INSTALLATION INSTRUCTIONS  
Step 1. Open the door on the stove and locate the stainless glass retainer  
(see Figure 1). Screws are located underneath the white door  
gasket, and directly in line with the identifying holes on the stain-  
less glass retainer.  
NOTE: DIAGRAMS AND ILLUSTRATIONS ARE NOT TO SCALE.  
Lennox Hearth Products reserves the right to make changes at any time, without notice, in design, materials, specifications, prices and also to discontinue colors, styles and products.  
Consult your local distributor for fireplace code information.  
Printed in U.S.A. © 2011 Lennox Hearth Products  
Lennox Hearth Products  
1508 Elm Hill Pike, Suite 108 • Nashville, TN 37210  
P/N 506033-57 Rev. NC 08/2011  
 

LevelOne Switch POH 0850TX User Manual
Linksys Speaker System DMSPK50 User Manual
Logitech Mouse M115 User Manual
Magnasonic Portable DVD Player MDVD654 User Manual
Manhattan Computer Products Computer Drive 179133 User Manual
Maytag Refrigerator MFI2266AEB10 User Manual
Maytag Water Heater HRE11240S User Manual
McIntosh Speaker HT 12 User Manual
Middleby Marshall Oven PS555 User Manual
Midland Radio Two Way Radio GXT800 User Manual