Linksys Network Card WAG110 User Manual

USER GUIDE  
Wireless ADSL2+ Gateway  
Models: WAG54G2, WAG200G,  
WAG110, WAG160N  
 
Table of Contents  
Wireless ADSL2+ Gateway  
ii  
 
Product Overview  
Chapter 1  
DSL (Green) The DSL LED lights up whenever  
there is a successful DSL connection. The LED  
flashes while the Gateway is establishing the  
ADSL connection.  
Chapter 1:  
Product Overview  
Internet (Green) The Internet LED lights up  
and stays on when there is a connection made  
through the Internet port. It flashes to indicate  
network activity over the Internet port.  
Thank you for choosing the Linksys Wireless ADSL2+  
Gateway. The Gateway lets you access the Internet via a  
wireless connection or through one of its four switched  
ports. You can also use the Gateway to share resources  
such as computers, printers and files. A variety of security  
features help to protect your data and your privacy while  
online. Security features include WPA2 security, a Stateful  
Packet Inspection (SPI) firewall and NAT technology.  
Configuring the Gateway is easy using the provided  
browser-based utility.  
Back Panel  
WAG54G2, WAG110, WAG160N  
Front Panel  
WAG200G  
WAG54G2, WAG110, WAG160N  
DSL The DSL port connects to the ADSL line.  
Ethernet 1, 2, 3, 4 These Ethernet ports (1, 2,  
3, 4) connect the Gateway to wired computers  
and other Ethernet network devices.  
WAG200G  
Power (Green) The Power LED lights up and  
stays on while the Gateway is powered on.  
Reset TherearetwowaystoresettheGateway’s  
factory defaults. Either press and hold the Reset  
buttonforapproximatelyfiveseconds,orrestore  
the defaults from the Administration > Factory  
Defaults screen of the Gateway’s web-based  
utility.  
Ethernet 1-4 (Green) These numbered LEDs,  
corresponding with the numbered ports on  
the Gateway’s back panel, serve two purposes.  
If the LED is continuously lit, the Gateway is  
successfully connected to a device through that  
port. It flashes to indicate network activity over  
that port.  
Power The Power port is where you will  
connect the power adapter.  
Wi-Fi Protected Setup Button (WAG54G2,  
WAG110, WAG160N Only) Press this button  
to allow Wi-Fi Protected Setup to search for  
your Wi-Fi Protected Setup-supported wireless  
device.  
Placement Positions  
There are two ways to physically install the device. The  
first way is to place the device horizontally on a surface.  
The second way is to mount the device on a wall.  
Horizontal Placement  
The device has four rubber feet on its bottom panel. Place  
the device on a level surface near an electrical outlet.  
NOTE: Wi-Fi Protected Setup is  
a
feature that makes it easy to configure  
your wireless network and its security  
settings. For more information, refer to  
“Wireless > Basic Wireless Settings“ in  
the “Advanced Configurationchapter.  
Wireless (Green) The Wireless LED lights up  
when the wireless feature is enabled. It flashes  
when the Gateway is actively sending or  
receiving data over the network.  
Wireless ADSL2+ Gateway  
1
 
 
Product Overview  
Chapter 1  
Follow these instructions:  
Wall-Mounting Placement  
1. Determine where you want to mount the device. Make  
sure that the wall you use is smooth, flat, dry, and  
sturdy. Also make sure the location is within reach of  
an electrical outlet.  
(WAG54G2, WAG110, WAG160N Only)  
The device has two wall-mount slots on its bottom  
panel. The distance between the slots is 152 mm  
(6 inches).  
2. Drill two holes into the wall. Make sure the holes are  
152 mm (6 inches) apart.  
Two screws are needed to mount the device.  
3. Insert a screw into each hole and leave 3 mm  
(0.12 inches) of its head exposed.  
Suggested Mounting Hardware  
4. Maneuver the device so the wall-mount slots line up  
with the two screws.  
4-5 mm  
1-1.5 mm  
5. Place the wall-mount slots over the screws and slide  
the device down until the screws fit snugly into the  
wall-mount slots.  
Note: Mounting hardware illustrations are not  
true to scale.  
NOTE: Linksys is not responsible for damages  
incurred by insecure wall-mounting hardware.  
152 mm  
Wall Mounting Template  
Wireless ADSL2+ Gateway  
2
 
Wireless Security Checklist  
Chapter 2  
Chapter 2:  
4. Enable encryption  
Wireless Security Checklist  
Encryption protects data transmitted over a wireless  
network. Wi-Fi Protected Access (WPA/WPA2) and Wired  
Equivalency Privacy (WEP) offer different levels of security  
for wireless communication.  
Wireless networks are convenient and easy to install, so  
homes with high-speed Internet access are adopting them  
at a rapid pace. Because wireless networking operates by  
sending information over radio waves, it can be more  
vulnerable to intruders than a traditional wired network.  
Like signals from your cellular or cordless phones, signals  
from your wireless network can also be intercepted. Since  
you cannot physically prevent someone from connecting  
to your wireless network, you need to take some additional  
steps to keep your network secure.  
A network encrypted with WPA/WPA2 is more secure  
than a network encrypted with WEP, because WPA/WPA2  
uses dynamic key encryption. To protect the information  
as it passes over the airwaves, you should enable the  
highest level of encryption supported by your network  
equipment.  
WEP is an older encryption standard and may be the  
only option available on some older devices that do not  
support WPA.  
1. Change the default wireless  
network name or SSID  
General Network Security Guidelines  
Wireless network security is useless if the underlying  
network is not secure.  
Wireless devices have a default wireless network name  
or Service Set Identifier (SSID) set by the factory. This  
is the name of your wireless network, and can be up  
to 32 characters in length. Linksys wireless products  
use linksys as the default wireless network name. You  
should change the wireless network name to something  
unique to distinguish your wireless network from other  
wireless networks that may exist around you, but do not  
use personal information (such as your Social Security  
number) because this information may be available for  
anyone to see when browsing for wireless networks.  
Password protect all computers on the network and  
individually password protect sensitive files.  
Change passwords on a regular basis.  
Install anti-virus software and personal firewall  
software.  
Disable file sharing (peer-to-peer). Some applications  
may open file sharing without your consent and/or  
knowledge.  
2. Change the default password  
Additional Security Tips  
For wireless products such as access points, routers, and  
gateways, you will be asked for a password when you  
want to change their settings.These devices have a default  
password set by the factory. The Linksys default password  
is admin. Hackers know these defaults and may try to  
use them to access your wireless device and change your  
network settings. To thwart any unauthorized changes,  
customize the device’s password so it will be hard to  
guess.  
Keep wireless routers, access points, or gateways away  
from exterior walls and windows.  
Turn wireless routers, access points, or gateways  
off when they are not being used (at night, during  
vacations).  
Usestrongpassphrasesthatareatleasteightcharacters  
in length. Combine letters and numbers to avoid using  
standard words that can be found in the dictionary.  
3. Enable MAC address filtering  
WEB: For more information on wireless  
Linksys routers and gateways give you the ability to  
enable Media Access Control (MAC) address filtering. The  
MAC address is a unique series of numbers and letters  
assigned to every networking device. With MAC address  
filtering enabled, wireless network access is provided  
solely for wireless devices with specific MAC addresses.  
For example, you can specify the MAC address of each  
computer in your home so that only those computers can  
access your wireless network.  
Wireless ADSL2+ Gateway  
3
 
 
Installation  
Chapter 3  
NOTE: To avoid interference, you may need to  
place a microfilter or splitter between the phone  
cableandwalljack. ContactyourISPtodetermine  
if one is required. (UK residents need to connect  
the microfilter to the wall phone jack with ADSL  
serviceandthenconnectoneendoftheprovided  
phone cable to the DSL port on it.) If you have  
more than one phone and you experience static  
on the line after installing the Gateway, then you  
need to install an additional microfilter for each  
phone or fax that you use. If you use ISDN, then  
you do not need a microfilter.  
Chapter 3:  
Installation  
Linksys strongly recommends that you run the Setup CD-  
ROM. If you have problems running the Setup CD-ROM,  
use this chapter.  
Connection  
1. Make sure that all the devices that you are working  
with are powered down, including your computer(s)  
and the Gateway. If you have a modem connected  
to your network, disconnect it. The Gateway replaces  
your modem.  
6. Connect the power adapter to the Gateway’s power  
port and the electrical outlet.  
2. Connect one end of the provided Ethernet cable to  
your computer’s Ethernet adapter. Connect the other  
end of the Ethernet cable to one of the Ethernet ports  
on the back of the Gateway.  
Connect the Power  
7. Power on the computer that you want to use to  
configure the Gateway.  
8. The Power, Wireless, and at least one of the numbered  
Ethernet (1, 2, 3, or 4) LEDs should light up. If not, make  
sure the Gateway is powered on and the cables are  
securely connected.  
Connect the Computer  
3. Repeat step 2 for every computer or device that you  
want to connect to the Gateway via Ethernet. If you  
connect more than four computers to the Gateway,  
you also need to connect a switch to the Gateway.  
Connection is complete.  
Continue to the “Setup” section.  
NOTE: If your computer’s Ethernet adapter  
is not set up, refer to the Ethernet adapter’s  
documentation for more information.  
Setup  
For setup, configure the Gateway to access the Internet  
through your ADSL Internet Service Provider (ISP). Use the  
setup information provided by your ISP.  
4. Connect one end of the phone cable to the DSL port  
on the back of the Gateway.  
Access the web-based utility as described in “Chapter 4:  
AdvancedConfiguration, andthencompletethefollowing  
tabs within the utility:  
Setup > Basic Setup  
Wireless > Basic Wireless Settings  
Wireless > Wireless Security  
Connect the DSL  
After completing the setup, to test it, enter  
www.linksys.com/uk/registration in the web browser’s  
Address field, and press Enter.  
5. Connect the other end of the phone cable to the wall  
jack with ADSL service or microfilter.  
Installation is complete.  
Wireless ADSL2+ Gateway  
4
 
 
Advanced Configuration  
Chapter 4  
How to Access the Web-Based Utility  
Chapter 4:  
Advanced Configuration  
After setting up the Gateway with the Setup Wizard  
(located on the CD-ROM), the Gateway will be ready  
for use. However, if you’d like to change its advanced  
settings, use the Gateway’s web-based utility. This chapter  
describes each web page of the utility and each page’s key  
functions. You can access the utility via a web browser on  
a computer connected to the Gateway.  
To access the web-based utility, launch the web browser  
on your computer, and enter the Gateway’s default IP  
address, 192.168.1.1, in the Address field. Then, press  
Enter.  
A login screen appears. Use the default user name and  
password, admin, unless you have changed them during  
the Setup Wizard. (You can set a new user name and  
password from the Administration tab’s Management  
screen.) Click OK to continue.  
The web-based utility has these main tabs: Setup,  
Wireless, Security, Access Restrictions, Applications &  
Gaming, Administration, and Status. Additional tabs will  
be available after you click one of the main tabs.  
NOTE: When first installing the Gateway, you  
should use the Setup Wizard on the Setup CD-  
ROM. If you want to configure advanced settings,  
use this chapter.  
Gateway Login  
If you are unable to log in, press the Reset button on the  
back panel for at least 5 seconds, then wait for the device  
to reset and try again.  
NOTE:ForNewZealand, followtheseinstructions  
after accessing the web-based utility in the  
Setup > Basic Setup screen:  
1. Select RFC 2364 PPPoA from the  
Encapsulation drop-down menu.  
2. For the Virtual Circuit ID, enter 0 for the VPI  
and 100 for the VCI.  
3. Select VC for Multiplexing.  
4. Select Multimode from the DSL Modulation  
drop-down menu.  
5. Enter your User Name and Password details  
from your ISP.  
6. Click Save Settings.  
Wireless ADSL2+ Gateway  
5
 
 
Troubleshooting  
Appendix A  
You need to modify the basic settings on the Gateway.  
Appendix A:  
Run the Setup Wizard on the Setup CD-ROM.  
Troubleshooting  
You need to modify the advanced settings on the  
Gateway.  
Your computer cannot connect to the Internet.  
Open the web browser (for example, Internet Explorer  
or Firefox), and enter the Gateway’s IP address in the  
address field (the default IP address is 192.168.1.1). When  
prompted, complete the User name and Password fields  
(the default user name and password is admin). Click the  
appropriate tab to change the settings  
Follow the instructions until your computer can connect  
to the Internet:  
Make sure that the Gateway is powered on. The Power  
LED should be green and not flashing.  
If the Power LED is flashing, then power off all of  
your network devices, including the Gateway and  
computers. Then power on each device in the  
following order:  
WEB: If your questions are not addressed  
here, refer to the Linksys website,  
1. Gateway  
2. Computer  
Check the LEDs on the front panel of the Gateway.  
Make sure the Power, DSL, and at least one of the  
numbered LEDs are lit. If they are not, then check  
the cable connections. The computer should be  
connected to one of the ports numbered 1-4 on the  
Gateway, and the Line port of the Gateway must be  
connected to the ADSL line.  
When you double-click the web browser, you are  
prompted for a username and password. If you want to  
get rid of the prompt, follow these instructions.  
Launch the web browser and perform the following steps  
(these steps are specific to Internet Explorer but are similar  
for other browsers):  
1. Select Tools > Internet Options.  
2. Click the Connections tab.  
3. Select Never dial a connection.  
4. Click OK.  
You are using a static IP address and cannot connect.  
Refer to Windows Help and change your Internet Protocol  
(TCP/IP) Properties to Obtain an IP address automatically.  
The computer cannot connect wirelessly to the network.  
Make sure the wireless network name or SSID is the  
same on both the computer and the Gateway. If you  
have enabled wireless security, then make sure the same  
security method and key are used by both the computer  
and the Gateway.  
Wireless ADSL2+ Gateway  
6
 
 
Specifications  
Appendix B  
Appendix B:  
Specifications  
Model  
WAG54G2  
Model  
WAG200G  
Standards  
802.11g, 802.11b, 802.3u,  
g.992.1 (g.dmt), g.992.2 (g.lite),  
g.992.3, g.992.5, T1.413i2,  
U-R2 for Annex B  
Standards  
IEEE 802.11g, IEEE 802.11b,  
IEEE 802.3u, IEEE 802.3,  
g.992.1 (g.dmt), g.992.2 (g.lite),  
g.992.3, g.992.5, T1.413i2,  
U-R2 for Annex B  
Ports  
DSL, Ethernet (1-4), Power  
Reset, Wi-Fi Prptected Setup  
Ports  
Line (or DSL), Ethernet (1-4), Power  
Reset  
Buttons  
LEDs  
Buttons  
LEDs  
Power, Ethernet, Wi-Fi Protected  
Setup, Wireless, DSL, Internet  
Power, Wireless, Ethernet (1-4), DSL,  
Internet  
Cabling Type  
Transmit Power  
UPnP  
CAT5 UTP, RJ-11, RJ-45  
Cabling Type  
Antennas  
CAT5 UTP, RJ-45, RJ-11  
1 Non-Detachable  
18 dBm  
18 dBm  
Able  
Transmit Power  
UPnP  
Security Features  
VPN Passthrough (IPSec, PPPoE,  
PPTP, L2TP), DoS Protection,  
WPA2/WPA Personal and  
Enterprise, WEP, MAC Address  
Filtering, NAT, SPI Firewall  
Able  
Security Features Password-Protected Configuration  
for Web Access  
PAP and CHAP Authentication  
Denial of Service (DoS) Prevention  
SPI Firewall Protection  
Routing &  
Management  
Protocols  
Static and Dynamic Routing,  
RIP (v1/v2), IGMP, QoS, WMM,  
UPnP, MAC Address Cloning  
URL Filtering, and Keyword, Java,  
ActiveX, Proxy, Cookie Blocking  
Environmental  
Dimensions  
202 x 34 x 160 mm  
(8.0" x 1.3" x 6.3")  
ToD Filter (Blocks Access by Time)  
VPN Passthrough for IPSec, PPTP, and  
L2TP Protocols  
Weight  
362 g (12.8 oz)  
12VDC, 1A  
Power  
WPA2, WPA; 128, 64 Bits WEP with  
Passphrase WEP Key Generation  
Certification  
FCC, UL, CE, IDA, Anatel, A-tick,  
Wi-Fi (802.11b, 802.11g), WPA,  
WPA2, Telepermit  
SSID Broadcast Disable  
Access Restriction by MAC and IP  
Addresses  
Operating Temp.  
Storage Temp.  
0 to 40°C (32 to 104°F)  
-20 to 70°C (-4 to 158°F)  
10 to 85% Noncondensing  
5 to 90% Noncondensing  
Security Key Bits 64, 128, 256  
Operating Humidity  
Storage Humidity  
Environmental  
Dimensions  
140 x 140 x 27 mm  
(5.51” x 5.51” x 1.25”)  
Weight  
350 g (12.35 oz)  
12VDC, 1A  
Power  
Certification  
CE, FCC, IC-03, Wi-Fi, A-tick,  
Telepermit, IDA, Anatel, WPA, WPA2  
Operating Temp. 0 to 40°C (32 to 104°F)  
Storage Temp.  
-20 to 70°C (-4 to 158°F)  
Operating  
Humidity  
10 to 85% Noncondensing  
Storage Humidity 5 to 90% Noncondensing  
Wireless ADSL2+ Gateway  
7
 
 
Specifications  
Appendix B  
Model  
WAG110  
Model Number  
Standards  
WAG160N  
Standards  
802.11g, 802.11b, 802.3u,  
g.992.1 (g.dmt), g.992.2 (g.lite),  
g.992.3, g.992.5, T1.413i2,  
U-R2 for Annex B  
Draft 802.11N, IEEE 802.11g,  
IEEE 802.11b, IEEE 802.3u,  
g.992.1 (g.dmt), g.992.2 (g.lite),  
g.992.3, g.992.5, T1.413i2 Issue 2,  
U-R2 for Annex B  
Ports  
DSL, Ethernet (1-4), Power  
Reset, Wi-Fi Prptected Setup  
Ports  
Power, DSL, Ethernet (1-4)  
Reset, Wi-Fi Protected Setup  
CAT5 UTP, RJ-45, RJ-11  
Buttons  
LEDs  
Buttons  
Cabling Type  
LEDs  
Power, Ethernet, Wi-Fi Protected  
Setup, Wireless, DSL, Internet  
Cabling Type  
Antennas  
CAT5 UTP, RJ-11, RJ-45  
Power, Wireless, Ethernet (1-4), DSL,  
Internet  
2 Internal  
17 dBm  
2 dBi  
Antennas  
2 Internal  
17 dBm  
2 dBi  
Trasmit Power  
Antenna Gain  
UPnP  
Transmit Power  
Antenna Gain  
Able  
Security Features Password-Protected Configuration  
for Web Access  
Security Features  
VPN Passthrough (IPSec,  
PPTP, L2TP), DoS Protection,  
WPA2/WPA Personal and  
Enterprise, WEP, MAC Address  
Filtering, NAT, SPI Firewall  
PAP and CHAP Authentication  
Denial of Service (DoS) Prevention  
SPI Firewall  
Routing &  
Management  
Protocols  
Static and Dynamic Routing,  
RIP (v1/v2), IGMP, QoS, WMM,  
UPnP, MAC Address Cloning  
AP Isolation  
URL Filtering, and Keyword, Java,  
ActiveX, Proxy, Cookie Blocking  
Environmental  
Dimensions  
ToD Filter (Blocks Access by Time)  
202 x 34 x 160 mm  
(8.0” x 1.3” x 6.3”)  
VPN Passthrough for IPSec, PPTP, and  
L2TP Protocols  
Weight  
362 g (12.8 oz)  
12VDC, 1A  
WPA, WPA2 Personal and Enterprise  
Power  
128, 64 Bits WEP with Passphrase  
WEP Key Generation  
Certification  
CE, Wi-Fi (802.11b, 802.11g),  
WPA, WPA2  
SSID Broadcast Disable  
Operating Temp.  
Storage Temp.  
0 to 40°C (32 to 104°F)  
Access Restriction by MAC and IP  
Addresses  
-20 to 70°C (-4 to 158°F)  
10 to 85% Noncondensing  
5 to 90% Noncondensing  
Operating Humidity  
Storage Humidity  
Environmental  
Dimensions  
Weight  
202 x 34 x 160 mm (8.0” x 1.3” x 6.3”)  
362 g (12.8 oz)  
Power  
12VDC, 1A  
Certification  
FCC, CE, IC-03, Wi-Fi, A-Tick,  
Telepermit, IDA, WPA, WPA2  
Operating Temp. 0 to 40°C (32 to 104°F)  
Storage Temp.  
-20 to 70°C (-4 to 158°F)  
Operating  
Humidity  
10 to 85% Noncondensing  
Storage Humidity 5 to 90% Noncondensing  
Wireless ADSL2+ Gateway  
8
 
Warranty Information  
Appendix C  
attacking networks, Linksys does not warrant that the  
product, service, software or any equipment, system or  
network on which the product or software is used will be  
free of vulnerability to intrusion or attack. The product  
may include or be bundled with third party software or  
service offerings. This limited warranty shall not apply to  
such third party software or service offerings. This limited  
warranty does not guarantee any continued availability  
of a third party’s service for which this product’s use or  
operation may require.  
Appendix C:  
Warranty Information  
Limited Warranty – Europe, Middle East,  
Africa, Latin America  
Linksys warrants that this Linksys hardware product will be  
substantially free of defects in materials and workmanship  
arising under normal use during the Warranty Period,  
which begins on the date of purchase by the original end-  
user purchaser and lasts for the period specified below:  
TO THE EXTENT NOT PROHIBITED BY LAW, ALL IMPLIED  
WARRANTIES AND CONDITIONS OF MERCHANTABILITY,  
SATISFACTORY QUALITY OR FITNESS FOR A PARTICULAR  
PURPOSE ARE LIMITED TO THE DURATION OF THE  
WARRANTY PERIOD. ALL OTHER EXPRESS OR IMPLIED  
CONDITIONS, REPRESENTATIONS AND WARRANTIES,  
INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED  
WARRANTY OF NON-INFRINGEMENT, ARE DISCLAIMED.  
Some jurisdictions do not allow limitations on how long  
an implied warranty lasts, so the above limitation may not  
apply to you. This limited warranty gives you specific legal  
rights, and you may also have other rights which vary by  
jurisdiction.  
Two (2) years for new product  
Ninety (90) days for refurbished product  
This limited warranty is non-transferable and extends only  
to the original end-user purchaser. Your exclusive remedy  
and Linksys’ entire liability under this limited warranty  
will be for Linksys, at its option, to (a) repair the product  
with new or refurbished parts, (b) replace the product  
with a reasonably available equivalent new or refurbished  
Linksys product, or (c) refund the purchase price of the  
product less any rebates. Any repaired or replacement  
products will be warranted for the remainder of the  
original Warranty Period or ninety (90) days, whichever is  
longer. All products and/or parts that are replaced become  
the property of Linksys.  
TO THE EXTENT NOT PROHIBITED BY LAW, IN NO EVENT  
WILL LINKSYS BE LIABLE FOR ANY LOST DATA, REVENUE  
OR PROFIT, OR FOR SPECIAL, INDIRECT, CONSEQUENTIAL,  
INCIDENTAL OR PUNITIVE DAMAGES, REGARDLESS OF THE  
THEORY OF LIABILITY (INCLUDING NEGLIGENCE), ARISING  
OUT OF OR RELATED TO THE USE OF OR INABILITY TO  
USE THE PRODUCT (INCLUDING ANY SOFTWARE), EVEN  
IF LINKSYS HAS BEEN ADVISED OF THE POSSIBILITY OF  
SUCH DAMAGES. IN NO EVENT WILL LINKSYS’ LIABILITY  
EXCEED THE AMOUNT PAID BY YOU FOR THE PRODUCT.  
The foregoing limitations will apply even if any warranty  
or remedy provided under this limited warranty fails of  
its essential purpose. Some jurisdictions do not allow  
the exclusion or limitation of incidental or consequential  
damages, so the above limitation or exclusion may not  
apply to you.  
This limited warranty shall apply in addition to any  
statutory or other rights which you may have under a  
contract of sale.  
Exclusions and Limitations  
This limited warranty does not apply if: (a) the product  
assembly seal has been removed or damaged, (b) the  
product has been altered or modified, except by Linksys,  
(c) the product damage was caused by use with non-  
Linksys products, (d) the product has not been installed,  
operated, repaired, or maintained in accordance with  
instructions supplied by Linksys, (e) the product has  
been subjected to abnormal physical or electrical stress,  
misuse, negligence, or accident, (f) the serial number on  
the Product has been altered, defaced, or removed, or (g)  
the product is supplied or licensed for beta, evaluation,  
testing or demonstration purposes for which Linksys does  
not charge a purchase price or license fee.  
Obtaining Warranty Service  
If you have a question about your product or experience  
where you will find a variety of online support tools  
and information to assist you with your product. For  
instructions on how to obtain warranty service in the event  
your product proves defective during the Warranty Period,  
contact the Service Provider from whom you purchased or  
received the product (or Linksys Technical Support if you  
did not purchase or receive the product from a Service  
Provider). The telephone number for Linksys Technical  
Support in your area can be found in the product User  
number and proof of purchase on hand when calling. A  
DATED PROOF OF ORIGINAL PURCHASE IS REQUIRED TO  
ALLSOFTWAREPROVIDEDBYLINKSYSWITHTHEPRODUCT,  
WHETHER FACTORY LOADED ON THE PRODUCT OR  
CONTAINED ON MEDIA ACCOMPANYING THE PRODUCT,  
IS PROVIDED “AS IS” WITHOUT ANY WARRANTY OF ANY  
KIND. Without limiting the foregoing, Linksys does not  
warrant that the operation of the product or software will  
be uninterrupted or error free. Also, due to the continual  
development of new techniques for intruding upon and  
Wireless ADSL2+ Gateway  
9
 
 
Warranty Information  
Appendix C  
PROCESS WARRANTY CLAIMS. If you are requested to  
return your product, you will be given a Return Materials  
Authorization (RMA) number. You are responsible for  
properly packaging and return shipping your product  
at your cost and risk. You must include the RMA number  
and a copy of your dated proof of original purchase when  
returning your product. Products received without a  
RMA number and dated proof of original purchase will  
be rejected. Do not include any other items with the  
product you are returning. Defective product covered  
by this limited warranty will be repaired or replaced and  
returned to you without charge. Customers outside of  
the United States of America and Canada are responsible  
for all shipping and handling charges, custom duties,  
VAT and other associated taxes and charges. Repairs or  
replacements not covered under this limited warranty will  
be subject to charge at the then-current rates.  
Limited Warranty – India, Indonesia,  
Malaysia, Phillipines, Singapore, Thailand,  
Vietnam  
Linksys warrants this Linksys hardware product against  
defects in materials and workmanship under normal  
use for the Warranty Period, which begins on the date of  
purchase by the original end-user purchaser and lasts for  
the period specified below:  
Two (2) years for new product  
Ninety (90) days for refurbished product  
This limited warranty is non-transferable and extends only  
to the original end-user purchaser. Your exclusive remedy  
and Linksys’ entire liability under this limited warranty  
will be for Linksys, at its option, to (a) repair the product  
with new or refurbished parts, (b) replace the product  
with a reasonably available equivalent new or refurbished  
Linksys product, or (c) refund the purchase price of the  
product less any rebates. Any repaired or replacement  
products will be warranted for the remainder of the  
original Warranty Period or thirty (30) days, whichever is  
longer. All products and parts that are replaced become  
the property of Linksys.  
Technical Support  
This limited warranty is neither a service nor a support  
contract. Information about Linksys’ current technical  
support offerings and policies (including any fees for  
support.  
General  
Exclusions and Limitations  
This limited warranty is governed by the laws of the  
jurisdiction in which the Product was purchased by you.  
This limited warranty does not apply if: (a) the product  
assembly seal has been removed or damaged, (b) the  
product has been altered or modified, except by Linksys,  
(c) the product damage was caused by use with non-  
Linksys products, (d) the product has not been installed,  
operated, repaired, or maintained in accordance with  
instructions supplied by Linksys, (e) the product has  
been subjected to abnormal physical or electrical stress,  
misuse, negligence, or accident, (f) the serial number on  
the Product has been altered, defaced, or removed, or (g)  
the product is supplied or licensed for beta, evaluation,  
testing or demonstration purposes for which Linksys does  
not charge a purchase price or license fee.  
If any portion of this limited warranty is found to be void  
or unenforceable, its remaining provisions shall remain in  
full force and effect.  
Please direct all inquiries to: Linksys, P.O. Box 18558, Irvine,  
CA 92623.  
For more information, please contact us  
Select your country, and then select SUPPORT/  
TECHNICAL  
For product returns:  
ALL SOFTWARE PROVIDED BY LINKSYS WITH THE  
PRODUCT, WHETHER FACTORY LOADED ON THE  
PRODUCT OR CONTAINED ON MEDIA ACCOMPANYING  
THE PRODUCT, IS PROVIDED “AS ISWITHOUT WARRANTY  
OF ANY KIND. Without limiting the foregoing, Linksys does  
not warrant that the operation of the product or software  
will be uninterrupted or error free. Also, due to the  
continual development of new techniques for intruding  
upon and attacking networks, Linksys does not warrant  
that the product, software or any equipment, system or  
network on which the product or software is used will be  
free of vulnerability to intrusion or attack. The product  
may include or be bundled with third party software or  
service offerings. This limited warranty shall not apply to  
such third party software or service offerings. This limited  
Select your Country and then select CUSTOMER SUPPORT  
Wireless ADSL2+ Gateway  
10  
 
 
Warranty Information  
Appendix C  
warranty does not guarantee any continued availability  
of a third party’s service for which this product’s use or  
operation may require.  
RMA number and dated proof of original purchase will  
be rejected. Do not include any other items with the  
product you are returning. Defective product covered  
by this limited warranty will be repaired or replaced and  
returned to you without charge. Customers outside of  
the United States of America and Canada are responsible  
for all shipping and handling charges, custom duties,  
VAT and other associated taxes and charges. Repairs or  
replacements not covered under this limited warranty will  
be subject to charge at the then-current rates.  
TO THE EXTENT NOT PROHIBITED BY LAW, ALL IMPLIED  
WARRANTIES AND CONDITIONS OF MERCHANTABILITY,  
SATISFACTORY QUALITY OR FITNESS FOR A PARTICULAR  
PURPOSE ARE LIMITED TO THE DURATION OF THE  
WARRANTY PERIOD. ALL OTHER EXPRESS OR IMPLIED  
CONDITIONS, REPRESENTATIONS AND WARRANTIES,  
INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED  
WARRANTY OF NON-INFRINGEMENT, ARE DISCLAIMED.  
Some jurisdictions do not allow limitations on how long  
an implied warranty lasts, so the above limitation may not  
apply to you. This limited warranty gives you specific legal  
rights, and you may also have other rights which vary by  
jurisdiction.  
Technical Support  
This limited warranty is neither a service nor a support  
contract. Information about Linksys’ current technical  
support offerings and policies (including any fees for  
support.  
TO THE EXTENT NOT PROHIBITED BY LAW, IN NO EVENT  
WILL LINKSYS BE LIABLE FOR ANY LOST DATA, REVENUE  
OR PROFIT, OR FOR SPECIAL, INDIRECT, CONSEQUENTIAL,  
INCIDENTAL OR PUNITIVE DAMAGES, REGARDLESS OF THE  
THEORY OF LIABILITY (INCLUDING NEGLIGENCE), ARISING  
OUT OF OR RELATED TO THE USE OF OR INABILITY TO  
USE THE PRODUCT (INCLUDING ANY SOFTWARE), EVEN  
IF LINKSYS HAS BEEN ADVISED OF THE POSSIBILITY OF  
SUCH DAMAGES. IN NO EVENT WILL LINKSYS’ LIABILITY  
EXCEED THE AMOUNT PAID BY YOU FOR THE PRODUCT.  
The foregoing limitations will apply even if any warranty  
or remedy provided under this limited warranty fails of  
its essential purpose. Some jurisdictions do not allow  
the exclusion or limitation of incidental or consequential  
damages, so the above limitation or exclusion may not  
apply to you.  
This limited warranty is governed by the laws of the  
jurisdiction in which the Linksys product was purchased  
by you.  
Please direct all inquiries to: Linksys, P.O. Box 18558, Irvine,  
CA 92623.  
Obtaining Warranty Service  
If you have a question about your product or experience  
where you will find a variety of online support tools  
and information to assist you with your product. For  
instructions on how to obtain warranty service in the event  
your product proves defective during the Warranty Period,  
contact the Service Provider from whom you purchased or  
received the product (or Linksys Technical Support if you  
did not purchase or receive the product from a Service  
Provider). The telephone number for Linksys Technical  
Support in your area can be found in the product User  
number and proof of purchase on hand when calling. A  
DATED PROOF OF ORIGINAL PURCHASE IS REQUIRED TO  
PROCESS WARRANTY CLAIMS. If you are requested to  
return your product, you will be given a Return Materials  
Authorization (RMA) number. You are responsible for  
properly packaging and return shipping your product  
at your cost and risk. You must include the RMA number  
and a copy of your dated proof of original purchase when  
returning your product. Products received without a  
Wireless ADSL2+ Gateway  
11  
 
Warranty Information  
Appendix C  
the product is supplied or licensed for beta, evaluation,  
testing or demonstration purposes for which Linksys does  
not charge a purchase price or license fee.  
Limited Warranty – Australia and New  
Zealand  
All software provided by Linksys with the product, whether  
factory loaded on the product or contained on media  
accompanying the product, is provided “as is. Without  
limiting the foregoing, Linksys does not warrant that the  
operation of the product or software will be uninterrupted  
orerrorfree.Also,duetothecontinualdevelopmentofnew  
techniques for intruding upon and attacking networks,  
Linksys does not warrant that the product, software or any  
equipment, system or network on which the product or  
software is used will be free of vulnerability to intrusion or  
attack. The product may include or be bundled with third  
party software or service offerings. This limited warranty  
shall not apply to such third party software or service  
offerings. This limited warranty does not guarantee any  
continued availability of a third party’s service for which  
this product’s use or operation may require.  
Linksys warrants this Linksys hardware product against  
defects in materials and workmanship under normal  
use for the Warranty Period, which begins on the date of  
purchase by the original end-user purchaser and lasts for  
the period specified below:  
Two (2) years for new product  
Ninety (90) days for refurbished product  
This limited warranty is non-transferable and extends only  
to the original end-user purchaser. Your exclusive remedy  
and Linksysentire liability under this limited warranty will  
be for Linksys, at its option, to (a) repair the product with  
new or refurbished parts, (b) replace the product with an  
equivalent new or refurbished Linksys product, (c) refund  
the actual purchase price of the product (net of rebates  
and discounts), or (d) pay the cost of repair of the product.  
Any repaired or replacement products will be warranted  
for the remainder of the original Warranty Period or thirty  
(30) days, whichever is longer. All products and parts that  
are replaced become the property of Linksys.  
To the extent permitted by law, Linksys excludes liability  
for any lost data, revenue or profit, and indirect or  
consequential loss, whether based in statute, common  
law (including negligence) or otherwise, arising out of  
or related to the use of or inability to use the product  
(including any software), even if Linksys has been advised  
of the possibility of such damages and Linksys limits its  
liability to an amount not exceeding the amount paid by  
you for the product.  
This limited warranty gives you specific legal rights, and  
you may also have other rights which vary by jurisdiction.  
Nothing in this limited warranty excludes, restricts or  
modifies any condition, warranty, right or remedy implied  
or imposed by any statute or regulation, including implied  
terms and warranties which operate to protect the  
purchasers of goods and services in various circumstances,  
which cannot lawfully be excluded, restricted or modified.  
These statutes and regulations include (in the case of  
Australia) Part V of the Trade Practices Act 1974 (C’th of  
Australia) and corresponding provisions of Australian State  
or Territory legislation, and (in the case of New Zealand)  
the Consumer Guarantees Act 1993 (NZ). Subject to the  
foregoing and without limiting express provisions of this  
limited warranty, all express or implied representations,  
conditions, warranties and provisions whether based in  
statute, common law or otherwise, relating to this Linksys  
hardware product, that are not contained in this limited  
warranty are excluded to the extent permitted by law.  
Obtaining Warranty Service  
If you have a question about your product or experience  
where you will find a variety of online support tools  
and information to assist you with your product. For  
instructions on how to obtain warranty service in the event  
your product proves defective during the Warranty Period,  
contact the Service Provider from whom you purchased or  
received the product (or Linksys Technical Support if you  
did not purchase or receive the product from a Service  
Provider). The telephone number for Linksys Technical  
Support in your area can be found in the product User  
number and proof of purchase on hand when calling. A  
DATED PROOF OF ORIGINAL PURCHASE IS REQUIRED TO  
PROCESS WARRANTY CLAIMS. If you are requested to  
return your product, you will be given a Return Materials  
Authorization (RMA) number. You are responsible for  
properly packaging and return shipping your product  
at your cost and risk. You must include the RMA number  
and a copy of your dated proof of original purchase when  
returning your product. Products received without a  
RMA number and dated proof of original purchase will  
be rejected. Do not include any other items with the  
product you are returning. Defective product covered  
by this limited warranty will be repaired or replaced and  
Exclusions and Limitations  
This limited warranty does not apply if: (a) the product  
assembly seal has been removed or damaged, (b) the  
product has been altered or modified, except by Linksys,  
(c) the product damage was caused by use with non-  
Linksys products, (d) the product has not been installed,  
operated, repaired, or maintained in accordance with  
instructions supplied by Linksys, (e) the product has  
been subjected to abnormal physical or electrical stress,  
misuse, negligence, or accident, (f) the serial number on  
the Product has been altered, defaced, or removed, or (g)  
Wireless ADSL2+ Gateway  
12  
 
 
Warranty Information  
Appendix C  
returned to you without charge. Customers outside of  
the United States of America and Canada are responsible  
for all shipping and handling charges, custom duties,  
VAT and other associated taxes and charges. Repairs or  
replacements not covered under this limited warranty will  
be subject to charge at the then-current rates.  
Technical Support  
This limited warranty is neither a service nor a support  
contract. Information about Linksys’ current technical  
support offerings and policies (including any fees for  
support.  
This limited warranty is governed by the laws of the  
jurisdiction in which the Product was purchased by you.  
If any portion of this limited warranty is found to be void  
or unenforceable, its remaining provisions shall remain in  
full force and effect.  
Please direct all inquiries to: Linksys, P.O. Box 18558, Irvine,  
CA 92623.  
Wireless ADSL2+ Gateway  
13  
 
Regulatory Information  
Appendix D  
FCC Part 68 Statement  
Appendix D:  
Regulatory Information  
This equipment complies with Part 68 of the FCC Rules. A  
label is attached to the equipment that contains, among  
other information, its FCC registration number and ringer  
equivalence number. If requested, this information must  
be provided to the telephone company.  
United States of America  
The following information applies if you use the product  
within the United States of America.  
This equipment uses the following USOC Jack: RJ-11.  
An FCC compliant telephone cord and modular plug  
is provided with this equipment. This equipment is  
designed to be connected to the telephone network or  
premises wiring using a compatible modular jack, which  
is FCC Part 68 compliant. Connection to the telephone  
network should be made by using the standard modular  
telephone jack.  
FCC Statement  
This device complies with Part 15 of the FCC Rules.  
Operation is subject to the following two conditions: (1)  
Thisdevicemaynotcauseharmfulinterference, and(2)this  
device must accept any interference received, including  
interference that may cause undesired operation.  
The REN is useful to determine the quantity of devices  
that may be connected to the telephone line and still have  
all of those devices ring when your telephone number is  
called. In most, but not all areas, the sum of RENs should  
not exceed 5. To be certain of the number of devices that  
may be connected to the line, as determined by the total  
RENs, contact the telephone company to determine the  
maximum REN for the calling area.  
This product has been tested and complies with the  
specifications for a Class B digital device, pursuant to Part  
15 of the FCC Rules. These limits are designed to provide  
reasonable protection against harmful interference in  
a residential installation. This equipment generates,  
uses, and can radiate radio frequency energy and, if not  
installed and used according to the instructions, may  
cause harmful interference to radio communications.  
However, there is no guarantee that interference will not  
occur in a particular installation. If this equipment does  
cause harmful interference to radio or television reception,  
which is found by turning the equipment off and on, the  
user is encouraged to try to correct the interference by  
one or more of the following measures:  
If this equipment causes harm to the telephone network,  
the telephone company may discontinue your service  
temporarily. If advance notice is not practical, the  
telephone company will notify the customer as soon as  
possible. Also, you will be advised of your right to file a  
complaint with the FCC if you believe it is necessary.  
The telephone company may make changes in its  
facilities, equipment, operations, or procedures that could  
affect the operation of the equipment. If this happens, the  
telephone company will provide advance notice in order  
for you to make the necessary modifications in order to  
maintain uninterrupted service.  
Reorient or relocate the receiving antenna  
Increase the separation between the equipment or  
devices  
Connect the equipment to an outlet other than the  
receiver’s  
In the event this equipment should fail to operate properly,  
disconnect the unit from the telephone line. Try using  
another FCC approved device in the same telephone  
jack. If the trouble persists, call the telephone company  
repair service bureau. If the trouble does not persist and  
appears to be with this unit, disconnect the unit from the  
telephone line and discontinue use of the unit until it is  
repaired. Please note that the telephone company may ask  
that you disconnect the equipment from the telephone  
network until the problem has been corrected or until  
you are sure that the equipment is not malfunctioning.  
The user must use the accessories and cables supplied by  
the manufacturer to get optimum performance from the  
product.  
Consult a dealer or an experienced radio/TV technician  
for assistance  
FCC Caution: Any changes or modifications not expressly  
approved by the party responsible for compliance could  
void the user’s authority to operate this equipment.  
FCC Radiation Exposure Statement  
This equipment complies with FCC radiation exposure  
limits set forth for an uncontrolled environment. This  
equipment should be installed and operated with  
minimum distance 20cm between the radiator and your  
body.  
This transmitter must not be co-located or operating in  
conjunction with any other antenna or transmitter. IEEE  
802.11b or 802.11g operation of this product in the USA is  
firmware-limited to channels 1 through 11.  
No repairs may be done by the customer. If trouble is  
experienced with this equipment, please contact your  
authorized support provider for repair and warranty  
information. If the trouble is causing harm to the  
telephone network, the telephone company may request  
Wireless ADSL2+ Gateway  
14  
 
 
Regulatory Information  
Appendix D  
you remove the equipment from the network until the  
problem is resolved. This equipment cannot be used on  
telephone company provided coin service. Connection to  
Party Line Service is subject to state tariffs.  
Operation is subject to the following two conditions:  
1. This device may not cause interference and  
2. This device must accept any interference, including  
interference that may cause undesired operation of the  
device. This device has been designed to operate with  
an antenna having a maximum gain of 2dBi. Antenna  
havingahighergainisstrictlyprohibitedperregulations  
of Industry Canada. The required antenna impedance  
is 50 ohms.  
Safety Notices  
Caution: To reduce the risk of fire, use only No.26 AWG  
or larger telecommunication line cord.  
Do not use this product near water, for example, in a  
wet basement or near a swimming pool.  
To reduce potential radio interference to other users,  
the antenna type and its gain should be so chosen  
that the EIRP is not more than required for successful  
communication.  
Avoid using this product during an electrical storm.  
There may be a remote risk of electric shock from  
lightning.  
Industry Canada Radiation Exposure Statement:  
WARNING: This equipment will be inoperable  
when main power fails.  
This equipment complies with IC radiation exposure limits  
set forth for an uncontrolled environment. This equipment  
should be installed and operated with minimum distance  
20cm between the radiator & your body.  
WARNING: To ensure compliance with  
explosure limits to radiofrequency fields, the  
antenna of the device should be no closer than  
20 cm from the body during use.  
This transmitter must not be co-located or operating in  
conjunction with any other antenna or transmitter.  
Avis d’Industrie Canada  
Canada  
Cet appareil est conforme aux normes NMB003 et RSS210  
d’Industrie Canada.  
The following information applies if you use the product  
within Canada.  
Lutilisation de ce dispositif est autorisée seulement aux  
conditions suivantes :  
Industry Canada Statement  
1. il ne doit pas produire de brouillage et  
This device complies with Industry Canada ICES-003 and  
RSS210 rules.  
2. il doit accepter tout brouillage radioélectrique reçu,  
mêmesicebrouillageestsusceptibledecompromettre  
le fonctionnement du dispositif. Le dispositif a été  
conçupourfonctionneravecuneantenneayantungain  
maximum de 2 dBi. Les règlements d’Industrie Canada  
interdisent strictement l’utilisation d’antennes dont le  
gain est supérieur à cette limite. L’impédance requise  
de l’antenne est de 50 ohms.  
Afin de réduire le risque d’interférence aux autres  
utilisateurs, le type d’antenne et son gain doivent  
être choisis de façon à ce que la puissance isotrope  
rayonnée équivalente (p.i.r.e.) ne soit pas supérieure  
au niveau requis pour obtenir une communication  
satisfaisante.  
Avis d’Industrie Canada concernant l’exposition aux radio-  
fréquences :  
Ce matériel est conforme aux limites établies par IC  
en matière d’exposition aux radiofréquences dans un  
environnement non contrôlé. Ce matériel doit être installé  
et utilisé à une distance d’au moins 20 cm entre l’antenne  
et le corps de l’utilisateur.  
Wireless ADSL2+ Gateway  
15  
 
 
Regulatory Information  
Appendix D  
L’émetteur ne doit pas être placé près d’une autre antenne  
ou d’un autre émetteur, ou fonctionner avec une autre  
antenne ou un autre émetteur.  
Това оборудване отговаря на съществените  
Б ъ л г а р с к и  
[Bulgarian]  
изисквания  
и
приложими клаузи на  
Директива 1999/5/ЕС.  
Wireless Disclaimer  
Toto zařízení je  
požadavky  
ustanoveními Směrnice 1999/5/EC.  
v
souladu se základními  
Česky  
[Czech]:  
a
ostatními odpovídajícími  
The maximum performance for wireless is derived from  
IEEE Standard 802.11 specifications. Actual performance  
can vary, including lower wireless network capacity,  
data throughput rate, range and coverage. Performance  
depends on many factors, conditions and variables,  
including distance from the access point, volume of  
network traffic, building materials and construction,  
operating system used, mix of wireless products used,  
interference and other adverse conditions.  
Dette udstyr er i overensstemmelse med  
de væsentlige krav og andre relevante  
bestemmelser i Direktiv 1999/5/EF.  
Dansk  
[Danish]:  
Dieses Gerät entspricht den grundlegenden  
Anforderungen  
entsprechenden Vorgaben der Richtlinie  
1999/5/EU.  
Deutsch  
[German]:  
und  
den  
weiteren  
Avis de non-responsabilité concernant les  
appareils sans fil  
Eesti  
[Estonian]:  
Seeseadevastabdirektiivi1999/5/EÜolulistele  
nõuetele ja teistele asjakohastele sätetele.  
Les performances maximales pour les réseaux sans fil  
sont tirées des spécifications de la norme IEEE 802.11.  
Les performances réelles peuvent varier, notamment  
en fonction de la capacité du réseau sans fil, du débit  
de la transmission de données, de la portée et de la  
couverture. Les performances dépendent de facteurs,  
conditions et variables multiples, en particulier de la  
distance par rapport au point d’accès, du volume du trafic  
réseau, des matériaux utilisés dans le bâtiment et du  
type de construction, du système d’exploitation et de la  
combinaison de produits sans fil utilisés, des interférences  
et de toute autre condition défavorable.  
This equipment is in compliance with the  
essential requirements and other relevant  
provisions of Directive 1999/5/EC.  
English:  
Este equipo cumple con los requisitos  
esenciales asi como con otras disposiciones  
de la Directiva 1999/5/CE.  
Español  
[Spanish]:  
Αυτός ο εξοπλισµός είναι σε συµµόρφωση µε  
τις ουσιώδεις απαιτήσεις και άλλες σχετικές  
διατάξεις της Οδηγίας 1999/5/EC.  
Ελληνική  
[Greek]:  
Cet appareil est conforme aux exigences  
essentielles et aux autres dispositions  
pertinentes de la Directive 1999/5/EC.  
Français  
[French]:  
New Zealand  
The following information applies if you use the product  
within New Zealand.  
Þetta tæki er samkvæmt grunnkröfum og  
öðrum viðeigandi ákvæðum Tilskipunar  
1999/5/EC.  
Íslenska  
[Icelandic]:  
Telepermit Statement  
The cabling between the phone port and the phone shall  
not exceed 100 metres.  
Questo apparato  
essenziali ed agli altri principi sanciti dalla  
Direttiva 1999/5/CE.  
é
conforme ai requisiti  
Italiano  
[Italian]:  
European Union  
The following information applies if you use the product  
within the European Union.  
Šī iekārta atbilst Direktīvas 1999/5/EK  
būtiskajām prasībām un citiem ar to  
saistītajiem noteikumiem.  
Latviski  
[Latvian]:  
Declaration of Conformity with Regard to EU  
Directive 1999/5/EC (R&TTE Directive)  
Šis įrenginys tenkina 1999/5/EB Direktyvos  
esminius reikalavimus ir kitas šios direktyvos  
nuostatas.  
Lietuvių  
[Lithuanian]:  
Compliance Information for 2,4-GHz and 5-GHz Wireless  
ProductsRelevanttotheEUandOtherCountriesFollowing  
the EU Directive 1999/5/EC (R&TTE Directive)  
Dit apparaat voldoet aan de essentiele eisen  
en andere van toepassing zijnde bepalingen  
van de Richtlijn 1999/5/EC.  
Nederlands  
[Dutch]:  
NOTE: The 5 GHz information does not apply to  
Wireless-G (802.11g) only products.  
Wireless ADSL2+ Gateway  
16  
 
 
Regulatory Information  
Appendix D  
The following standards were applied during the  
assessment of the product against the requirements of  
the Directive 1999/5/EC:  
Dan l-apparat huwa konformi mal-ħtiġiet  
essenzjali u l-provedimenti l-oħra rilevanti  
tad-Direttiva 1999/5/EC.  
Malti  
[Maltese]:  
Radio: EN 300 328 and/or EN 301 893 as applicable  
EMC: EN 301 489-1, EN 301 489-17  
Ez  
a
készülék teljesíti az alapvető  
Magyar  
[Hungarian]:  
követelményeket  
irányelvben  
rendelkezéseket.  
és  
más  
1999/5/EK  
vonatkozó  
meghatározott  
Safety: EN 60950 and either EN 50385 or EN 50371  
Dynamic Frequency Selection (DFS) and Transmit Power  
Control (TPC) are required for operation in the 5 GHz  
band.  
Dette utstyret er  
grunnleggende krav og andre relevante  
bestemmelser i EU-direktiv 1999/5/EF.  
i
samsvar med de  
Norsk  
[Norwegian]:  
DFS: The equipment meets the DFS requirements as  
defined in ETSI EN 301 893. This feature is required by  
the regulations to avoid interference with Radio Location  
Services (radars).  
Urządzenie jest zgodne  
wymaganiami oraz szczególnymi warunkami  
określonymi Dyrektywą UE: 1999/5/EC.  
z
ogólnymi  
Polski  
[Polish]:  
TPC: For operation in the 5 GHz band, the maximum power  
level is 3 dB or more below the applicable limit. As such,  
TPC is not required.  
Este equipamento está em conformidade com  
os requisitos essenciais e outras provisões  
relevantes da Directiva 1999/5/EC.  
Português  
[Portuguese]:  
CE Marking  
Acest echipament este in conformitate  
cu cerintele esentiale si cu alte prevederi  
relevante ale Directivei 1999/5/EC.  
Română  
[Romanian]  
For the Linksys Wireless-N, -G, -B, and/or -A products,  
the following CE mark, notified body number (where  
applicable), and class 2 identifier are added to the  
equipment.  
Ta naprava je skladna z bistvenimi zahtevami  
in ostalimi relevantnimi pogoji Direktive  
1999/5/EC.  
Slovensko  
[Slovenian]:  
Toto zariadenie je v zhode so základnými  
požiadavkamiainýmipríslušnýminariadeniami  
direktív: 1999/5/EC.  
Slovensky  
[Slovak]:  
or  
or  
or  
Tämä laite täyttää direktiivin 1999/5/EY  
olennaiset vaatimukset ja on siinä asetettujen  
muiden laitetta koskevien määräysten  
mukainen.  
Suomi  
[Finnish]:  
Denna utrustning är i överensstämmelse med  
de väsentliga kraven och andra relevanta  
bestämmelser i Direktiv 1999/5/EC.  
Svenska  
[Swedish]:  
For all products, the Declaration of Conformity (DofC) is  
available through one or more of these options:  
Check the CE label on the product to find out which  
notified body was involved during the assessment.  
A pdf file is included on the product’s CD.  
A print copy is included with the product.  
A pdf file is available on the product’s webpage.  
Visit www.linksys.com/international and select your  
country or region. Then select your product.  
If you need any other technical documentation, see the  
Technical Documents on www.linksys.com/international”  
section, as shown later in this appendix.  
Wireless ADSL2+ Gateway  
17  
 
Regulatory Information  
Appendix D  
France  
National Restrictions  
For 2,4 GHz, the product should not be used outdoors  
in the band 2454 - 2483,5 MHz. There are no restrictions  
when used in other parts of the 2,4 GHz band when used  
This product may be used in all EU countries (and other  
countries following the EU directive 1999/5/EC) without  
any limitation except for the countries mentioned below:  
Ce produit peut être utilisé dans tous les pays de l’UE (et dans  
tous les pays ayant transposés la directive 1999/5/CE) sans  
aucune limitation, excepté pour les pays mentionnés ci-  
dessous:  
Pour la bande 2,4 GHz, l’ équipement ne doit pas être utilisé  
en extérieur dans la bande 2454 - 2483,5 MHz. Il n’y a pas de  
restrictions pour des utilisations en intérieur dans d’autres  
pour de plus amples détails.  
Questo prodotto è utilizzabile in tutte i paesi EU (ed in tutti  
gli altri paesi che seguono le direttive EU 1999/5/EC) senza  
nessuna limitazione, eccetto per i paesii menzionati di  
seguito:  
Applicable Power Levels in France  
Frequency  
Range (MHz)  
Location  
Power (EIRP)  
Das Produkt kann in allen EU Staaten ohne Einschränkungen  
eingesetzt werden (sowie in anderen Staaten die der EU  
Direktive 1999/5/CE folgen) mit Außnahme der folgenden  
aufgeführten Staaten:  
Indoor  
(No restrictions)  
2400-2483.5  
100 mW (20 dBm)  
In the majority of the EU and other European countries,  
the 2,4- and 5-GHz bands have been made available  
for the use of wireless local area networks (LANs). The  
table labeled “Overview of Regulatory Requirements for  
Wireless LANs” provides an overview of the regulatory  
requirements applicable for the 2,4- and 5-GHz bands.  
2400-2454  
2454-2483.5  
100 mW (20 dBm)  
10 mW (10 dBm)  
Outdoor  
Italy  
This product meets the National Radio Interface and  
the requirements specified in the National Frequency  
Allocation Table for Italy. Unless this 2,4-GHz wireless LAN  
product is operating within the boundaries of the owner’s  
property, its use requires a “general authorization. Please  
Later in this document you will find an overview of  
countries in which additional restrictions or requirements  
or both are applicable.  
The requirements for any country may evolve. Linksys  
recommends that you check with the local authorities for  
the latest status of their national regulations for both the  
2,4- and 5-GHz wireless LANs.  
Questo prodotto è conforme alla specifiche di Interfaccia  
Radio Nazionali e rispetta il Piano Nazionale di ripartizione  
delle frequenze in Italia. Se non viene installato all’interno  
del proprio fondo, l’utilizzo di prodotti Wireless LAN a  
2,4 GHz richiede una “Autorizzazione Generale. Consultare  
Overview of Regulatory Requirements for Wireless LANs  
Frequency  
Band (MHz)  
Max Power Level Indoor  
Indoor &  
Outdoor  
(EIRP) (mW)  
ONLY  
2400-2483.5  
5150-5350†  
5470-5725†  
100  
X
Latvia  
200  
X
The outdoor usage of the 2,4 GHz band requires an  
authorization from the Electronic Communications Office.  
1000  
X
Dynamic Frequency Selection and Transmit Power Control are  
required in the frequency ranges of 5250-5350 MHz and 5470-5725  
MHz.  
2,4 GHz frekveču joslas izmantošanai ārpus telpām  
nepieciešama atļauja no Elektronisko sakaru direkcijas.  
The following countries have restrictions and/or  
requirements in addition to those given in the table  
labeled “Overview of Regulatory Requirements for  
Wireless LANs”:  
Notes:  
1. Although Norway, Switzerland and Liechtenstein are  
not EU member states, the EU Directive 1999/5/EC has  
also been implemented in those countries.  
Denmark  
2. The regulatory limits for maximum output power are  
specified in EIRP. The EIRP level of a device can be  
calculated by adding the gain of the antenna used  
(specified in dBi) to the output power available at the  
connector (specified in dBm).  
In Denmark, the band 5150 - 5350 MHz is also allowed for  
outdoor usage.  
I Danmark må frekvensbåndet 5150 - 5350 også anvendes  
udendørs.  
Wireless ADSL2+ Gateway  
18  
 
Regulatory Information  
Appendix D  
Product Usage Restrictions  
This product is designed for indoor usage only. Outdoor  
usage is not recommended, unless otherwise noted.  
User Information for Consumer Products Covered  
by EU Directive 2002/96/EC on Waste Electric and  
Electronic Equipment (WEEE)  
2,4 GHz Restrictions  
This document contains important information for users  
with regards to the proper disposal and recycling of  
Linksys products. Consumers are required to comply with  
this notice for all electronic products bearing the following  
symbol:  
This product is designed for use with the standard, integral  
or dedicated (external) antenna(s) that is/are shipped  
together with the equipment. However, some applications  
may require the antenna(s), if removable, to be separated  
from the product and installed remotely from the device  
by using extension cables. For these applications, Linksys  
offers an R-SMA extension cable (AC9SMA) and an R-TNC  
extension cable (AC9TNC). Both of these cables are 9  
meters long and have a cable loss (attenuation) of 5 dB. To  
compensate for the attenuation, Linksys also offers higher  
gain antennas, the HGA7S (with R-SMA connector) and  
HGA7T (with R-TNC connector). These antennas have a  
gain of 7 dBi and may only be used with either the R-SMA  
or R-TNC extension cable.  
English - Environmental Information for Customers in  
the European Union  
Combinations of extension cables and antennas resulting  
in a radiated power level exceeding 100 mW EIRP are  
illegal.  
European Directive 2002/96/EC requires that the equipment  
bearing this symbol on the product and/or its packaging must  
not be disposed of with unsorted municipal waste. The symbol  
indicates that this product should be disposed of separately  
from regular household waste streams. It is your responsibility to  
dispose of this and other electric and electronic equipment via  
designated collection facilities appointed by the government or  
local authorities. Correct disposal and recycling will help prevent  
potential negative consequences to the environment and  
human health. For more detailed information about the disposal  
of your old equipment, please contact your local authorities,  
waste disposal service, or the shop where you purchased the  
product.  
Third-Party Software or Firmware  
The use of software or firmware not supported/provided  
by Linksys may result that the equipment is no longer  
compliant with the regulatory requirements.  
Technical Documents on  
Follow these steps to access technical documents:  
Български (Bulgarian)  
опазването на околната среда за потребители в  
Европейския съюз  
Европейска директива 2002/96/EC изисква уредите, носещи  
този символ върху изделието и/или опаковката му, да не  
се изхвърля т с несортирани битови отпадъци. Символът  
обозначава, че изделието трябва да се изхвърля отделно от  
сметосъбирането на обикновените битови отпадъци. Ваша  
е отговорността този и другите електрически и електронни  
уреди да се изхвърлят в предварително определени от  
държавните или общински органи специализирани пунктове  
-
Информация относно  
web browser.  
2. Select the country or region in which you live.  
3. Click the Products tab.  
4. Select the appropriate product category.  
5. Select the product sub-category, if necessary.  
6. Select the product.  
7. Select the type of documentation you want from the  
More Information section. The document will open  
in PDF format if you have Adobe Acrobat installed on  
your computer.  
за събиране. Правилното изхвърляне  
и
рециклиране  
ще спомогнат да се предотвратят евентуални вредни за  
околната среда и здравето на населението последствия. За  
по-подробна информация относно изхвърлянето на вашите  
стари уреди се обърнете към местните власти, службите за  
сметосъбиране или магазина, от който сте закупили уреда.  
NOTE: If you have questions regarding  
the compliance of this product or you  
cannot find the information you need,  
please contact your local sales office or visit  
Wireless ADSL2+ Gateway  
19  
 
Regulatory Information  
Appendix D  
Ceština (Czech) - Informace o ochraně životního  
prostředí pro zákazníky v zemích Evropské unie  
Eesti (Estonian)  
Euroopa Liidus asuvatele klientidele  
-
Keskkonnaalane informatsioon  
Evropská směrnice 2002/96/ES zakazuje, aby zařízení označené  
tímto symbolem na produktu anebo na obalu bylo likvidováno  
s netříděným komunálním odpadem. Tento symbol udává,  
že daný produkt musí být likvidován odděleně od běžného  
komunálního odpadu. Odpovídáte za likvidaci tohoto produktu  
a dalších elektrických a elektronických zařízení prostřednictvím  
určených sběrných míst stanovených vládou nebo místními  
Euroopa Liidu direktiivi 2002/96/EÜ nõuete kohaselt on  
seadmeid, millel on tootel või pakendil käesolev sümbol  
,
keelatud kõrvaldada koos sorteerimata olmejäätmetega. See  
sümbol näitab, et toode tuleks kõrvaldada eraldi tavalistest  
olmejäätmevoogudest. Olete kohustatud kõrvaldama käesoleva  
ja ka muud elektri- ja elektroonikaseadmed riigi või kohalike  
ametiasutuste poolt ette nähtud kogumispunktide kaudu.  
Seadmete korrektne kõrvaldamine ja ringlussevõtt aitab vältida  
võimalikke negatiivseid tagajärgi keskkonnale ning inimeste  
tervisele. Vanade seadmete kõrvaldamise kohta täpsema  
informatsiooni saamiseks võtke palun ühendust kohalike  
ametiasutustega, jäätmekäitlusfirmaga või kauplusega, kust te  
toote ostsite.  
úřady. Správná likvidace  
a
recyklace pomáhá předcházet  
potenciálním negativním dopadům na životní prostředí a lidské  
zdraví. Podrobnější informace o likvidaci starého vybavení si  
laskavě vyžádejte od místních úřadů, podniku zabývajícího se  
likvidací komunálních odpadů nebo obchodu, kde jste produkt  
zakoupili.  
Dansk (Danish) - Miljøinformation for kunder i EU  
Español (Spanish) - Información medioambiental para  
clientes de la Unión Europea  
EU-direktiv 2002/96/EF kræver, at udstyr der bærer dette symbol  
på produktet og/eller emballagen ikke må bortskaffes som  
usorteret kommunalt affald. Symbolet betyder, at dette produkt  
skal bortskaffes adskilt fra det almindelige husholdningsaffald.  
Det er dit ansvar at bortskaffe dette og andet elektrisk og  
elektronisk udstyr via bestemte indsamlingssteder udpeget  
af staten eller de lokale myndigheder. Korrekt bortskaffelse  
og genvinding vil hjælpe med til at undgå mulige skader for  
miljøet og menneskers sundhed. Kontakt venligst de lokale  
myndigheder, renovationstjenesten eller den butik, hvor du  
har købt produktet, angående mere detaljeret information om  
bortskaffelse af dit gamle udstyr.  
La Directiva 2002/96/CE de la UE exige que los equipos que  
lleven este símbolo en el propio aparato y/o en su embalaje  
no deben eliminarse junto con otros residuos urbanos no  
seleccionados. El símbolo indica que el producto en cuestión  
debe separarse de los residuos domésticos convencionales con  
vistas a su eliminación. Es responsabilidad suya desechar este y  
cualesquiera otros aparatos eléctricos y electrónicos a través de  
los puntos de recogida que ponen a su disposición el gobierno y  
lasautoridadeslocales. Aldesecharyreciclarcorrectamenteestos  
aparatos estará contribuyendo a evitar posibles consecuencias  
negativas para el medio ambiente y la salud de las personas. Si  
desea obtener información más detallada sobre la eliminación  
segura de su aparato usado, consulte a las autoridades locales,  
al servicio de recogida y eliminación de residuos de su zona o  
pregunte en la tienda donde adquirió el producto.  
Deutsch (German) - Umweltinformation für Kunden  
innerhalb der Europäischen Union  
Die Europäische Richtlinie 2002/96/EC verlangt, dass technische  
Ausrüstung, die direkt am Gerät und/oder an derVerpackung mit  
diesem Symbol versehen ist , nicht zusammen mit unsortiertem  
Gemeindeabfall entsorgt werden darf. Das Symbol weist darauf  
hin, dass das Produkt von regulärem Haushaltmüll getrennt  
entsorgt werden sollte. Es liegt in Ihrer Verantwortung, dieses  
Gerät und andere elektrische und elektronische Geräte über  
die dafür zuständigen und von der Regierung oder örtlichen  
Behörden dazu bestimmten Sammelstellen zu entsorgen.  
Ordnungsgemäßes Entsorgen und Recyceln trägt dazu bei,  
potentielle negative Folgen für Umwelt und die menschliche  
Gesundheit zu vermeiden. Wenn Sie weitere Informationen zur  
Entsorgung Ihrer Altgeräte benötigen, wenden Sie sich bitte an  
die örtlichen Behörden oder städtischen Entsorgungsdienste  
oder an den Händler, bei dem Sie das Produkt erworben haben.  
ξλληνικά (Greek)  
προστασίας για πελάτες εντός της Ευρωπαϊκής  
Ένωσης  
-
Στοιχεία περιβαλλοντικής  
ΗΚοινοτικήΟδηγία2002/96/ECαπαιτείότιοεξοπλισμόςοοποίος  
φέρει αυτό το σύμβολο στο προϊόν και/ή στη συσκευασία  
του δεν πρέπει να απορρίπτεται μαζί με τα μικτά κοινοτικά  
απορρίμματα. Το σύμβολο υποδεικνύει ότι αυτό το προϊόν θα  
πρέπει να απορρίπτεται ξεχωριστά από τα συνήθη οικιακά  
απορρίμματα. Είστε υπεύθυνος για την απόρριψη του παρόντος  
και άλλου ηλεκτρικού και ηλεκτρονικού εξοπλισμού μέσω των  
καθορισμένων εγκαταστάσεων συγκέντρωσης απορριμμάτων οι  
οποίες παρέχονται από το κράτος ή τις αρμόδιες τοπικές αρχές.  
Η σωστή απόρριψη και ανακύκλωση συμβάλλει στην πρόληψη  
πιθανών αρνητικών συνεπειών για το περιβάλλον και την υγεία.  
Για περισσότερες πληροφορίες σχετικά με την απόρριψη του  
παλιού σας εξοπλισμού, παρακαλώ επικοινωνήστε με τις τοπικές  
αρχές, τις υπηρεσίες απόρριψης ή το κατάστημα από το οποίο  
αγοράσατε το προϊόν.  
Wireless ADSL2+ Gateway  
20  
 
Regulatory Information  
Appendix D  
Français (French) - Informations environnementales  
pour les clients de l’Union européenne  
Lietuvškai (Lithuanian) - Aplinkosaugos informacija,  
skirta Europos Sąjungos vartotojams  
La directive européenne 2002/96/CE exige que l’équipement  
sur lequel est apposé ce symbole sur le produit et/ou son  
emballage ne soit pas jeté avec les autres ordures ménagères. Ce  
symbole indique que le produit doit être éliminé dans un circuit  
distinct de celui pour les déchets des ménages. Il est de votre  
responsabilité de jeter ce matériel ainsi que tout autre matériel  
électrique ou électronique par les moyens de collecte indiqués  
par le gouvernement et les pouvoirs publics des collectivités  
territoriales. L’élimination et le recyclage en bonne et due forme  
ont pour but de lutter contre l’impact néfaste potentiel de ce  
type de produits sur l’environnement et la santé publique. Pour  
plus d’informations sur le mode d’élimination de votre ancien  
équipement, veuillez prendre contact avec les pouvoirs publics  
locaux, le service de traitement des déchets, ou l’endroit où vous  
avez acheté le produit.  
Europos direktyva 2002/96/EC numato, kad įrangos, kuri ir  
kurios pakuotė yra pažymėta šiuo simboliu (įveskite simbolį),  
negalima šalinti kartu su nerūšiuotomis komunalinėmis  
atliekomis. Šis simbolis rodo, kad gaminį reikia šalinti atskirai  
nuo bendro buitinių atliekų srauto. Jūs privalote užtikrinti, kad  
ši ir kita elektros ar elektroninė įranga būtų šalinama per tam  
tikras nacionalinės ar vietinės valdžios nustatytas atliekų rinkimo  
sistemas. Tinkamai šalinant ir perdirbant atliekas, bus išvengta  
galimos žalos aplinkai ir žmonių sveikatai. Daugiau informacijos  
apie jūsų senos įrangos šalinimą gali pateikti vietinės valdžios  
institucijos, atliekų šalinimo tarnybos arba parduotuvės, kuriose  
įsigijote tą gaminį.  
Malti (Maltese) - Informazzjoni Ambjentali għal Klijenti  
fl-Unjoni Ewropea  
Id-Direttiva Ewropea 2002/96/KE titlob li t-tagħmir li jkun fih is-  
simbolu fuq il-prodott u/jew fuq l-ippakkjar ma jistax jintrema  
ma’ skart muniċipali li ma ġiex isseparat. Is-simbolu jindika  
li dan il-prodott għandu jintrema separatament minn ma’ l-  
iskart domestiku regolari. Hija responsabbiltà tiegħek li tarmi  
dan it-tagħmir u kull tagħmir ieħor ta’ l-elettriku u elettroniku  
permezz ta’ faċilitajiet ta’ ġbir appuntati apposta mill-gvern jew  
mill-awtoritajiet lokali. Ir-rimi b’mod korrett u r-riċiklaġġ jgħin  
jipprevjeni konsegwenzi negattivi potenzjali għall-ambjent u  
għas-saħħa tal-bniedem. Għal aktar informazzjoni dettaljata  
dwar ir-rimi tat-tagħmir antik tiegħek, jekk jogħġbok ikkuntattja  
lill-awtoritajiet lokali tiegħek, is-servizzi għar-rimi ta’ l-iskart, jew  
il-ħanut minn fejn xtrajt il-prodott.  
Italiano (Italian) - Informazioni relative all’ambiente  
per i clienti residenti nell’Unione Europea  
La direttiva europea 2002/96/EC richiede che le apparecchiature  
contrassegnate con questo simbolo  
sul prodotto e/o  
sull’imballaggio non siano smaltite insieme ai rifiuti urbani  
non differenziati. Il simbolo indica che questo prodotto non  
deve essere smaltito insieme ai normali rifiuti domestici. È  
responsabilità del proprietario smaltire sia questi prodotti sia  
le altre apparecchiature elettriche ed elettroniche mediante  
le specifiche strutture di raccolta indicate dal governo o dagli  
enti pubblici locali. Il corretto smaltimento ed il riciclaggio  
aiuteranno a prevenire conseguenze potenzialmente negative  
per l’ambiente e per la salute dell’essere umano. Per ricevere  
informazioni più dettagliate circa lo smaltimento delle vecchie  
apparecchiature in Vostro possesso, Vi invitiamo a contattare gli  
enti pubblici di competenza, il servizio di smaltimento rifiuti o il  
negozio nel quale avete acquistato il prodotto.  
Magyar (Hungarian) - Környezetvédelmi információ az  
európai uniós vásárlók számára  
A 2002/96/EC számú európai uniós irányelv megkívánja, hogy  
azokat a termékeket, amelyeken, és/vagy amelyek csomagolásán  
az alábbi címke megjelenik, tilos a többi szelektálatlan lakossági  
hulladékkal együtt kidobni. A címke azt jelöli, hogy az adott  
termék kidobásakor a szokványos háztartási hulladékelszállítási  
rendszerektõl elkülönített eljárást kell alkalmazni. Az Ön  
felelõssége, hogy ezt, és más elektromos és elektronikus  
berendezéseit a kormányzati vagy a helyi hatóságok által  
kijelölt gyűjtõredszereken keresztül számolja fel. A megfelelõ  
hulladékfeldolgozás segít a környezetre és az emberi egészségre  
potenciálisan ártalmas negatív hatások megelõzésében. Ha  
elavult berendezéseinek felszámolásához további részletes  
információra van szüksége, kérjük, lépjen kapcsolatba a helyi  
hatóságokkal, a hulladékfeldolgozási szolgálattal, vagy azzal  
üzlettel, ahol a terméket vásárolta.  
Latviešu valoda (Latvian) - Ekoloģiska informācija  
klientiem Eiropas Savienības jurisdikcijā  
Direktīvā 2002/96/EK ir prasība, ka aprīkojumu, kam pievienota  
zīme uz paša izstrādājuma vai uz tā iesaiņojuma, nedrīkst  
izmest nešķirotā veidā kopā ar komunālajiem atkritumiem  
(tiem, ko rada vietēji iedzīvotāji un uzņēmumi). Šī zīme nozīmē  
to, ka šī ierīce ir jāizmet atkritumos tā, lai tā nenonāktu kopā ar  
parastiem mājsaimniecības atkritumiem. Jūsu pienākums ir šo  
un citas elektriskas un elektroniskas ierīces izmest atkritumos,  
izmantojot īpašus atkritumu savākšanas veidus un līdzekļus, ko  
nodrošina valsts un pašvaldību iestādes. Ja izmešana atkritumos  
un pārstrāde tiek veikta pareizi, tad mazinās iespējamais  
kaitējums dabai un cilvēku veselībai. Sīkākas ziņas par  
novecojuša aprīkojuma izmešanu atkritumos jūs varat saņemt  
vietējā pašvaldībā, atkritumu savākšanas dienestā, kā arī veikalā,  
kur iegādājāties šo izstrādājumu.  
Wireless ADSL2+ Gateway  
21  
 
Regulatory Information  
Appendix D  
Nederlands (Dutch) - Milieu-informatie voor klanten  
in de Europese Unie  
Português (Portuguese) - Informação ambiental para  
clientes da União Europeia  
De Europese Richtlijn 2002/96/EC schrijft voor dat apparatuur die  
is voorzien van dit symbool op het product of de verpakking,  
niet mag worden ingezameld met niet-gescheiden huishoudelijk  
afval. Dit symbool geeft aan dat het product apart moet worden  
ingezameld. U bent zelf verantwoordelijk voor de vernietiging  
vandezeenandereelektrischeenelektronischeapparatuurviade  
daarvoor door de landelijke of plaatselijke overheid aangewezen  
inzamelingskanalen. De juiste vernietiging en recycling van  
deze apparatuur voorkomt mogelijke negatieve gevolgen voor  
het milieu en de gezondheid. Voor meer informatie over het  
vernietigen van uw oude apparatuur neemt u contact op met  
de plaatselijke autoriteiten of afvalverwerkingsdienst, of met de  
winkel waar u het product hebt aangeschaft.  
A Directiva Europeia 2002/96/CE exige que o equipamento  
que exibe este símbolo no produto e/ou na sua embalagem  
não seja eliminado junto com os resíduos municipais não  
separados.  
O
símbolo indica que este produto deve ser  
eliminado separadamente dos resíduos domésticos regulares.  
É da sua responsabilidade eliminar este e qualquer outro  
equipamento eléctrico e electrónico através das instalações  
de recolha designadas pelas autoridades governamentais ou  
locais. A eliminação e reciclagem correctas ajudarão a prevenir  
as consequências negativas para o ambiente e para a saúde  
humana. Para obter informações mais detalhadas sobre a  
forma de eliminar o seu equipamento antigo, contacte as  
autoridades locais, os serviços de eliminação de resíduos ou o  
estabelecimento comercial onde adquiriu o produto.  
Norsk (Norwegian) - Miljøinformasjon for kunder i EU  
Română (Romanian) - Informaţii de mediu pentru  
clienţii din Uniunea Europeană  
EU-direktiv 2002/96/EF krever at utstyr med følgende symbol  
avbildet på produktet og/eller pakningen, ikke må kastes  
sammen med usortert avfall. Symbolet indikerer at dette  
produktet skal håndteres atskilt fra ordinær avfallsinnsamling  
for husholdningsavfall. Det er ditt ansvar å kvitte deg med  
dette produktet og annet elektrisk og elektronisk avfall via egne  
innsamlingsordninger slik myndighetene eller kommunene  
bestemmer. Korrekt avfallshåndtering og gjenvinning vil  
være med på å forhindre mulige negative konsekvenser for  
miljø og helse. For nærmere informasjon om håndtering av  
det kasserte utstyret ditt, kan du ta kontakt med kommunen,  
en innsamlingsstasjon for avfall eller butikken der du kjøpte  
produktet.  
Directiva europeană 2002/96/CE impune ca echipamentele care  
prezintă acest simbol pe produs şi/sau pe ambalajul acestuia să  
nu fie casate împreună cu gunoiul menajer municipal. Simbolul  
indică faptul că acest produs trebuie să fie casat separat de  
gunoiul menajer obişnuit. Este responsabilitatea dvs. să casaţi  
acest produs şi alte echipamente electrice şi electronice prin  
intermediul unităţilor de colectare special desemnate de guvern  
sau de autorităţile locale. Casarea şi reciclarea corecte vor ajuta  
la prevenirea potenţialelor consecinţe negative asupra sănătăţii  
mediului şi a oamenilor. Pentru mai multe informaţii detaliate  
cu privire la casarea acestui echipament vechi, contactaţi  
autorităţile locale, serviciul de salubrizare sau magazinul de la  
care aţi achiziţionat produsul.  
Polski (Polish) - Informacja dla klientów w Unii  
Europejskiej  
środowiska  
o
przepisach dotyczących ochrony  
Slovenčina (Slovak) - Informácie o ochrane životného  
prostredia pre zákazníkov v Európskej únii  
Dyrektywa Europejska 2002/96/EC wymaga, aby sprzęt  
oznaczony symbolem znajdującym się na produkcie i/lub jego  
opakowaniu nie był wyrzucany razem z innymi niesortowanymi  
odpadami komunalnymi. Symbol ten wskazuje, że produkt  
nie powinien być usuwany razem ze zwykłymi odpadami z  
gospodarstw domowych. Na Państwu spoczywa obowiązek  
Podľa európskej smernice 2002/96/ES zariadenie  
s
týmto  
symbolom  
likvidované spolu  
na produkte a/alebo jeho balení nesmie byť  
s
netriedeným komunálnym odpadom.  
Symbol znamená, že produkt by sa mal likvidovať oddelene  
od bežného odpadu z domácností. Je vašou povinnosťou  
likvidovať toto i ostatné elektrické a elektronické zariadenia  
prostredníctvom špecializovaných zberných zariadení určených  
vládou alebo miestnymi orgánmi. Správna likvidácia a recyklácia  
pomôže zabrániť prípadným negatívnym dopadom na životné  
prostredie a zdravie ľudí. Ak máte záujem o podrobnejšie  
informácie o likvidácii starého zariadenia, obráťte sa, prosím, na  
miestne orgány, organizácie zaoberajúce sa likvidáciou odpadov  
alebo obchod, v ktorom ste si produkt zakúpili.  
wyrzucania tego  
i
innych urządzeń elektrycznych oraz  
elektronicznychwpunktachodbioruwyznaczonychprzezwładze  
krajowe lub lokalne. Pozbywanie się sprzętu we właściwy sposób  
i jego recykling pomogą zapobiec potencjalnie negatywnym  
konsekwencjom dla środowiska i zdrowia ludzkiego. W celu  
uzyskania szczegółowych informacji o usuwaniu starego sprzętu,  
prosimy zwrócić się do lokalnych władz, służb oczyszczania  
miasta lub sklepu, w którym produkt został nabyty.  
Wireless ADSL2+ Gateway  
22  
 
Regulatory Information  
Appendix D  
Slovenčina (Slovene) - Okoljske informacije za stranke  
v Evropski uniji  
Evropska direktiva 2002/96/EC prepoveduje odlaganje opreme,  
označene s tem simbolom – na izdelku in/ali na embalaži – med  
običajne, nerazvrščene odpadke. Ta simbol opozarja, da je treba  
izdelek odvreči ločeno od preostalih gospodinjskih odpadkov.  
Vaša odgovornost je, da to in preostalo električno in elektronsko  
opremo odnesete na posebna zbirališča, ki jih določijo  
državne ustanove ali lokalna uprava. S pravilnim odlaganjem  
in recikliranjem boste preprečili morebitne škodljive vplive na  
okolje in zdravje ljudi. Če želite izvedeti več o odlaganju stare  
opreme, se obrnite na lokalno upravo, odpad ali trgovino, kjer  
ste izdelek kupili.  
Suomi (Finnish) - Ympäristöä koskevia tietoja EU-  
alueen asiakkaille  
EU-direktiivi 2002/96/EY edellyttää, että jos laitteistossa on tämä  
symboli  
itse tuotteessa ja/tai sen pakkauksessa, laitteistoa  
ei saa hävittää lajittelemattoman yhdyskuntajätteen mukana.  
Symboli merkitsee sitä, että tämä tuote on hävitettävä erillään  
tavallisesta kotitalousjätteestä. Sinun vastuullasi on hävittää  
tämä elektroniikkatuote ja muut vastaavat elektroniikkatuotteet  
viemällä tuote tai tuotteet viranomaisten määräämään  
keräyspisteeseen. Laitteiston oikea hävittäminen estää  
mahdolliset kielteiset vaikutukset ympäristöön ja ihmisten  
terveyteen. Lisätietoja vanhan laitteiston oikeasta hävitystavasta  
saa paikallisilta viranomaisilta, jätteenhävityspalvelusta tai siitä  
myymälästä, josta ostit tuotteen.  
Svenska (Swedish) - Miljöinformation för kunder i  
Europeiska unionen  
Det europeiska direktivet 2002/96/EC kräver att utrustning med  
denna symbol på produkten och/eller förpackningen inte får  
kastas med osorterat kommunalt avfall. Symbolen visar att denna  
produktbörkastasefterattdenavskiljtsfrånvanligthushållsavfall.  
Det faller på ditt ansvar att kasta denna och annan elektrisk och  
elektronisk utrustning på fastställda insamlingsplatser utsedda  
av regeringen eller lokala myndigheter. Korrekt kassering och  
återvinning skyddar mot eventuella negativa konsekvenser  
för miljön och personhälsa. För mer detaljerad information om  
kassering av din gamla utrustning kontaktar du dina lokala  
myndigheter, avfallshanteringen eller butiken där du köpte  
produkten.  
WEB: For additional information, please visit  
Wireless ADSL2+ Gateway  
23  
 
Software License Agreement  
Appendix E  
Schedule 1 - Linksys Software License Agreement  
Appendix E: Software  
License Agreement  
THIS LICENSE AGREEMENT IS BETWEEN YOU AND  
CISCO-LINKSYS LLC OR ONE OF ITS AFFILIATES CISCO  
SYSTEMS-LINKSYS (ASIA) PTE LTD. OR CISCO-LINKSYS  
K.K. (“LINKSYS”) LICENSING THE SOFTWARE INSTEAD OF  
CISCO-LINKSYS LLC. BY DOWNLOADING OR INSTALLING  
THE SOFTWARE, OR USING THE PRODUCT CONTAINING  
THE SOFTWARE, YOU ARE CONSENTING TO BE BOUND BY  
THIS AGREEMENT. IFYOU DO NOT AGREE TO ALL OF THESE  
TERMS, THEN YOU MAY NOT DOWNLOAD, INSTALL OR USE  
THE SOFTWARE. YOU MAY RETURN UNUSED SOFTWARE  
(OR, IF THE SOFTWARE IS SUPPLIED AS PART OF ANOTHER  
PRODUCT, THE UNUSED PRODUCT) FOR A FULL REFUND  
UP TO 30 DAYS AFTER ORIGINAL PURCHASE, SUBJECT TO  
THE RETURN PROCESS AND POLICIES OF THE PARTY FROM  
WHICH YOU PURCHASED SUCH PRODUCT OR SOFTWARE.  
Software in Linksys Products  
This product from Cisco-Linksys LLC or from one of its  
affiliates Cisco Systems-Linksys (Asia) Pte Ltd. or Cisco-  
Linksys K.K. (“Linksys”) contains software (including  
firmware) originating from Linksys and its suppliers  
and may also contain software from the open source  
community. Any software originating from Linksys and its  
suppliers is licensed under the Linksys Software License  
Agreement contained at Schedule 1 below. You may also  
be prompted to review and accept that Linksys Software  
License Agreement upon installation of the software.  
License. Subject to the terms and conditions of this  
Agreement, Linksys grants the original end user purchaser  
of the Linksys product containing the Software (“You”)  
a nonexclusive license to use the Software solely as  
embedded in or (where authorized in the applicable  
documentation) for communication with such product.  
This license may not be sublicensed, and is not transferable  
except to a person or entity to which you transfer  
ownership of the complete Linksys product containing  
the Software, provided you permanently transfer all rights  
under this Agreement and do not retain any full or partial  
copies of the Software, and the recipient agrees to the  
terms of this Agreement.  
Any software from the open source community is licensed  
under the specific license terms applicable to that software  
made available by Linksys at www.linksys.com/gpl or as  
provided for in Schedules 2 and 3 below.  
Where such specific license terms entitle you to the source  
code of such software, that source code is upon request  
available at cost from Linksys for at least three years  
from the purchase date of this product and may also be  
available for download from www.linksys.com/gpl. For  
detailed license terms and additional information on  
open source software in Linksys products please look at  
the Linksys public web site at: www.linksys.com/gpl/ or  
Schedule 2 below as applicable.  
“Software” includes, and this Agreement will apply to (a)  
the software of Linksys or its suppliers provided in or with  
the applicable Linksys product, and (b) any upgrades,  
updates, bug fixes or modified versions (“Upgrades”) or  
backup copies of the Software supplied to You by Linksys  
or an authorized reseller, provided you already hold a  
valid license to the original software and have paid any  
applicable fee for the Upgrade.  
BY DOWNLOADING OR INSTALLING THE SOFTWARE,  
OR USING THE PRODUCT CONTAINING THE SOFTWARE,  
YOU ARE CONSENTING TO BE BOUND BY THE SOFTWARE  
LICENSE AGREEMENTS BELOW. IF YOU DO NOT AGREE TO  
ALL OF THESE TERMS, THEN YOU MAY NOT DOWNLOAD,  
INSTALL OR USE THE SOFTWARE. YOU MAY RETURN  
UNUSED SOFTWARE (OR, IF THE SOFTWARE IS SUPPLIED  
AS PART OF ANOTHER PRODUCT, THE UNUSED PRODUCT)  
FOR A FULL REFUND UP TO 30 DAYS AFTER ORIGINAL  
PURCHASE, SUBJECT TO THE RETURN PROCESS AND  
POLICIES OF THE PARTY FROM WHICH YOU PURCHASED  
SUCH PRODUCT OR SOFTWARE.  
Protection of Information. The Software and  
documentation contain trade secrets and/or copyrighted  
materials of Linksys or its suppliers. You will not copy  
or modify the Software or decompile, decrypt, reverse  
engineer or disassemble the Software (except to the  
extent expressly permitted by law notwithstanding this  
provision), and You will not disclose or make available  
such trade secrets or copyrighted material in any form  
to any third party. Title to and ownership of the Software  
and documentation and any portion thereof, will remain  
solely with Linksys or its suppliers.  
Software Licenses  
The software Licenses applicable to software from Linksys  
are made available at the Linksys public web site at:  
and  
respectively. For your convenience of reference, a copy  
of the Linksys Software License Agreement and the main  
open source code licenses used by Linksys in its products  
are contained in the Schedules below.  
Collection and Processing of Information. You agree that  
Linksys and/or its affiliates may, from time to time, collect  
and process information about your Linksys product  
and/or the Software and/or your use of either in order  
(i) to enable Linksys to offer you Upgrades; (ii) to ensure  
that your Linksys product and/or the Software is being  
Wireless ADSL2+ Gateway  
24  
 
 
Software License Agreement  
Appendix E  
used in accordance with the terms of this Agreement;  
(iii) to provide improvements to the way Linksys delivers  
technology to you and to other Linksys customers; (iv) to  
enableLinksystocomplywiththetermsofanyagreements  
it has with any third parties regarding your Linksys  
product and/or Software and/or (v) to enable Linksys to  
comply with all applicable laws and/or regulations, or the  
requirements of any regulatory authority or government  
agency. Linksys and/ or its affiliates may collect and  
process this information provided that it does not identify  
you personally. Your use of your Linksys product and/or  
the Software constitutes this consent by you to Linksys  
and/or its affiliatescollection and use of such information  
and, for EEA customers, to the transfer of such information  
to a location outside the EEA.  
SOFTWARE, EVEN IF LINKSYS HAS BEEN ADVISED OF  
THE POSSIBILITY OF SUCH DAMAGES. IN NO EVENT WILL  
LINKSYS’ LIABILITY EXCEED THE AMOUNT PAID BY YOU  
FOR THE PRODUCT. The foregoing limitations will apply  
even if any warranty or remedy under this Agreement fails  
of its essential purpose. Some jurisdictions do not allow  
the exclusion or limitation of incidental or consequential  
damages, so the above limitation or exclusion may not  
apply to You.  
Export. Software, including technical data, may be subject  
to U.S. export control laws and regulations and/or export  
or import regulations in other countries. You agree to  
comply strictly with all such laws and regulations.  
U.S. Government Users.The Software and documentation  
qualify as “commercial items” as defined at 48 C.F.R. 2.101  
and 48 C.F.R. 12.212. All Government users acquire the  
Software and documentation with only those rights  
herein that apply to non-governmental customers.  
Software Upgrades etc. If the Software enables you to  
receive Upgrades, you may elect at any time to receive  
these Upgrades either automatically or manually. If you  
elect to receive Upgrades manually or you otherwise  
elect not to receive or be notified of any Upgrades, you  
may expose your Linksys product and/or the Software  
to serious security threats and/or some features within  
your Linksys product and/or Software may become  
inaccessible. There may be circumstances where we  
apply an Upgrade automatically in order to comply with  
changes in legislation, legal or regulatory requirements  
or as a result of requirements to comply with the terms  
of any agreements Linksys has with any third parties  
regarding your Linksys product and/or the Software. You  
will always be notified of any Upgrades being delivered  
to you. The terms of this license will apply to any such  
Upgrade unless the Upgrade in question is accompanied  
by a separate license, in which event the terms of that  
license will apply.  
General Terms. This Agreement will be governed by and  
construed in accordance with the laws of the State of  
California, without reference to conflict of laws principles.  
The United Nations Convention on Contracts for the  
International Sale of Goods will not apply. If any portion  
of this Agreement is found to be void or unenforceable,  
the remaining provisions will remain in full force and  
effect. This Agreement constitutes the entire agreement  
between the parties with respect to the Software and  
supersedes any conflicting or additional terms contained  
in any purchase order or elsewhere.  
END OF SCHEDULE 1  
Schedule 2  
If this Linksys product contains open source software  
licensed under Version 2 of the “GNU General Public  
License” then the license terms below in this Schedule 2  
will apply to that open source software. The license terms  
below in this Schedule 2 are from the public web site at  
Open Source Software. The GPL or other open source  
code incorporated into the Software and the open source  
licenseforsuchsourcecodeareavailableforfreedownload  
at http://www.linksys.com/gpl. If You would like a copy  
of the GPL or other open source code in this Software on a  
CD, Linksys will mail to You a CD with such code for $9.99  
plus the cost of shipping, upon request.  
GNU GENERAL PUBLIC LICENSE  
Term and Termination. You may terminate this License  
at any time by destroying all copies of the Software  
and documentation. Your rights under this License will  
terminate immediately without notice from Linksys if You  
fail to comply with any provision of this Agreement.  
Version 2, June 1991  
Copyright © 1989, 1991 Free Software Foundation, Inc.  
51 Franklin Street, Fifth Floor, Boston, MA 02110-1301,  
USA  
Limited Warranty. The warranty terms and period  
specified in the applicable Linksys Product User Guide  
shall also apply to the Software.  
Everyone is permitted to copy and distribute verbatim  
copies of this license document, but changing it is not  
allowed.  
Disclaimer of Liabilities. IN NO EVENT WILL LINKSYS OR  
ITS SUPPLIERS BE LIABLE FOR ANY LOST DATA, REVENUE  
OR PROFIT, OR FOR SPECIAL, INDIRECT, CONSEQUENTIAL,  
INCIDENTAL OR PUNITIVE DAMAGES, REGARDLESS OF  
CAUSE (INCLUDING NEGLIGENCE), ARISING OUT OF  
OR RELATED TO THE USE OF OR INABILITY TO USE THE  
Preamble  
The licenses for most software are designed to take away  
your freedom to share and change it. By contrast, the  
GNU General Public License is intended to guarantee your  
Wireless ADSL2+ Gateway  
25  
 
Software License Agreement  
Appendix E  
freedom to share and change free software–to make sure  
the software is free for all its users. This General Public  
License applies to most of the Free Software Foundation’s  
software and to any other program whose authors  
commit to using it. (Some other Free Software Foundation  
software is covered by the GNU Lesser General Public  
License instead.) You can apply it to your programs, too.  
TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND  
MODIFICATION  
0. This License applies to any program or other work  
which contains a notice placed by the copyright  
holder saying it may be distributed under the terms  
of this General Public License. The “Program, below,  
refers to any such program or work, and a “work  
based on the Program” means either the Program  
or any derivative work under copyright law: that is  
to say, a work containing the Program or a portion  
of it, either verbatim or with modifications and/  
or translated into another language. (Hereinafter,  
translation is included without limitation in the term  
“modification.) Each licensee is addressed as “you.  
When we speak of free software, we are referring to  
freedom, not price. Our General Public Licenses are  
designed to make sure that you have the freedom to  
distribute copies of free software (and charge for this  
service if you wish), that you receive source code or can  
get it if you want it, that you can change the software or  
use pieces of it in new free programs; and that you know  
you can do these things.  
To protect your rights, we need to make restrictions that  
forbid anyone to deny you these rights or to ask you to  
surrender the rights. These restrictions translate to certain  
responsibilities for you if you distribute copies of the  
software, or if you modify it.  
Activities other than copying, distribution and  
modification are not covered by this License; they  
are outside its scope. The act of running the Program  
is not restricted, and the output from the Program is  
covered only if its contents constitute a work based on  
the Program (independent of having been made by  
running the Program). Whether that is true depends  
on what the Program does.  
For example, if you distribute copies of such a program,  
whether gratis or for a fee, you must give the recipients  
all the rights that you have. You must make sure that they,  
too, receive or can get the source code. And you must  
show them these terms so they know their rights.  
1. You may copy and distribute verbatim copies of the  
Program’s source code as you receive it, in any medium,  
provided that you conspicuously and appropriately  
publish on each copy an appropriate copyright  
notice and disclaimer of warranty; keep intact all the  
notices that refer to this License and to the absence  
of any warranty; and give any other recipients of the  
Program a copy of this License along with the Program.  
We protect your rights with two steps: (1) copyright the  
software, and (2) offer you this license which gives you  
legal permission to copy, distribute and/or modify the  
software.  
Also, for each author’s protection and ours, we want to  
make certain that everyone understands that there is no  
warranty for this free software. If the software is modified  
by someone else and passed on, we want its recipients  
to know that what they have is not the original, so that  
any problems introduced by others will not reflect on the  
original authorsreputations.  
You may charge a fee for the physical act of transferring  
a copy, and you may at your option offer warranty  
protection in exchange for a fee.  
2. You may modify your copy or copies of the Program  
or any portion of it, thus forming a work based on the  
Program, and copy and distribute such modifications  
or work under the terms of Section 1 above, provided  
that you also meet all of these conditions:  
Finally, any free program is threatened constantly by  
software patents. We wish to avoid the danger that  
redistributors of a free program will individually obtain  
patent licenses, in effect making the program proprietary.  
To prevent this, we have made it clear that any patent must  
be licensed for everyone’s free use or not licensed at all.  
a. You must cause the modified files to carry  
prominent notices stating that you changed the  
files and the date of any change.  
The precise terms and conditions for copying, distribution  
and modification follow.  
b. You must cause any work that you distribute or  
publish, that in whole or in part contains or is  
derived from the Program or any part thereof, to be  
licensed as a whole at no charge to all third parties  
under the terms of this License.  
Wireless ADSL2+ Gateway  
26  
 
Software License Agreement  
Appendix E  
c. If the modified program normally reads commands  
c. Accompany it with the information you received as  
totheoffertodistributecorrespondingsourcecode.  
(This alternative is allowed only for noncommercial  
distribution and only if you received the program  
in object code or executable form with such an  
offer, in accord with Subsection b above.)  
interactively when run, you must cause it, when  
started running for such interactive use in the most  
ordinary way, to print or display an announcement  
including an appropriate copyright notice and  
a notice that there is no warranty (or else, saying  
that you provide a warranty) and that users may  
redistribute the program under these conditions,  
and telling the user how to view a copy of  
this License. (Exception: if the Program itself is  
interactive but does not normally print such an  
announcement, your work based on the Program  
is not required to print an announcement.)  
The source code for a work means the preferred form  
of the work for making modifications to it. For an  
executable work, complete source code means all  
the source code for all modules it contains, plus any  
associated interface definition files, plus the scripts  
used to control compilation and installation of the  
executable. However, as a special exception, the source  
code distributed need not include anything that is  
normally distributed (in either source or binary form)  
with the major components (compiler, kernel, and so  
on) of the operating system on which the executable  
runs, unless that component itself accompanies the  
executable.  
These requirements apply to the modified work as  
a whole. If identifiable sections of that work are not  
derived from the Program, and can be reasonably  
considered independent and separate works in  
themselves, then this License, and its terms, do not  
apply to those sections when you distribute them as  
separate works. But when you distribute the same  
sections as part of a whole which is a work based on  
the Program, the distribution of the whole must be on  
the terms of this License, whose permissions for other  
licensees extend to the entire whole, and thus to each  
and every part regardless of who wrote it.  
If distribution of executable or object code is made  
by offering access to copy from a designated place,  
then offering equivalent access to copy the source  
code from the same place counts as distribution of  
the source code, even though third parties are not  
compelled to copy the source along with the object  
code.  
Thus, it is not the intent of this section to claim rights  
or contest your rights to work written entirely by you;  
rather, the intent is to exercise the right to control the  
distribution of derivative or collective works based on  
the Program.  
1. You may not copy, modify, sublicense, or distribute  
the Program except as expressly provided under  
this License. Any attempt otherwise to copy, modify,  
sublicense or distribute the Program is void, and will  
automatically terminate your rights under this License.  
However, parties who have received copies, or rights,  
from you under this License will not have their licenses  
terminated so long as such parties remain in full  
compliance.  
In addition, mere aggregation of another work not  
based on the Program with the Program (or with a  
work based on the Program) on a volume of a storage  
or distribution medium does not bring the other work  
under the scope of this License.  
2. You are not required to accept this License, since you  
have not signed it. However, nothing else grants you  
permission to modify or distribute the Program or its  
derivative works. These actions are prohibited by law if  
you do not accept this License.Therefore, by modifying  
or distributing the Program (or any work based on the  
Program), you indicate your acceptance of this License  
to do so, and all its terms and conditions for copying,  
distributing or modifying the Program or works based  
on it.  
1. You may copy and distribute the Program (or a  
work based on it, under Section 2) in object code or  
executable form under the terms of Sections 1 and 2  
above provided that you also do one of the following:  
a. Accompany it with the complete corresponding  
machine-readable source code, which must be  
distributed under the terms of Sections 1 and 2  
above on a medium customarily used for software  
interchange; or,  
b. Accompany it with a written offer, valid for at least  
three years, to give any third party, for a charge  
no more than your cost of physically performing  
source distribution, a complete machine-readable  
copy of the corresponding source code, to be  
distributed under the terms of Sections 1 and 2  
above on a medium customarily used for software  
interchange; or,  
3. Each time you redistribute the Program (or any work  
based on the Program), the recipient automatically  
receives a license from the original licensor to copy,  
distribute or modify the Program subject to these  
terms and conditions. You may not impose any further  
restrictions on the recipients’ exercise of the rights  
granted herein. You are not responsible for enforcing  
compliance by third parties to this License.  
Wireless ADSL2+ Gateway  
27  
 
Software License Agreement  
Appendix E  
4. If, as a consequence of a court judgment or allegation  
of patent infringement or for any other reason (not  
limited to patent issues), conditions are imposed on  
you (whether by court order, agreement or otherwise)  
that contradict the conditions of this License, they do  
not excuse you from the conditions of this License. If  
you cannot distribute so as to satisfy simultaneously  
your obligations under this License and any other  
pertinent obligations, then as a consequence you  
may not distribute the Program at all. For example,  
if a patent license would not permit royalty-free  
redistribution of the Program by all those who receive  
copies directly or indirectly through you, then the only  
way you could satisfy both it and this License would be  
to refrain entirely from distribution of the Program.  
not specify a version number of this License, you  
may choose any version ever published by the Free  
Software Foundation.  
1. If you wish to incorporate parts of the Program into  
other free programs whose distribution conditions are  
different, write to the author to ask for permission. For  
software which is copyrighted by the Free Software  
Foundation, write to the Free Software Foundation; we  
sometimes make exceptions for this. Our decision will  
be guided by the two goals of preserving the free status  
of all derivatives of our free software and of promoting  
the sharing and reuse of software generally.  
NO WARRANTY  
1. BECAUSETHEPROGRAMISLICENSEDFREEOFCHARGE,  
THERE IS NO WARRANTY FOR THE PROGRAM, TO THE  
EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT  
WHENOTHERWISESTATEDINWRITINGTHECOPYRIGHT  
HOLDERS AND/OR OTHER PARTIES PROVIDE THE  
PROGRAM “AS IS” WITHOUT WARRANTY OF ANY  
KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING,  
BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF  
MERCHANTABILITY AND FITNESS FOR A PARTICULAR  
PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND  
PERFORMANCE OF THE PROGRAM IS WITH YOU.  
SHOULD THE PROGRAM PROVE DEFECTIVE, YOU  
ASSUME THE COST OF ALL NECESSARY SERVICING,  
REPAIR OR CORRECTION.  
If any portion of this section is held invalid or  
unenforceable under any particular circumstance,  
the balance of the section is intended to apply and  
the section as a whole is intended to apply in other  
circumstances.  
It is not the purpose of this section to induce you to  
infringe any patents or other property right claims or  
to contest validity of any such claims; this section has  
the sole purpose of protecting the integrity of the free  
software distribution system, which is implemented  
by public license practices. Many people have  
made generous contributions to the wide range of  
software distributed through that system in reliance  
on consistent application of that system; it is up to  
the author/donor to decide if he or she is willing to  
distribute software through any other system and a  
licensee cannot impose that choice.  
2. INNOEVENTUNLESSREQUIREDBYAPPLICABLELAWOR  
AGREEDTO INWRITINGWILL ANY COPYRIGHT HOLDER,  
OR ANY OTHER PARTY WHO MAY MODIFY AND/OR  
REDISTRIBUTE THE PROGRAM AS PERMITTED ABOVE,  
BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY  
GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL  
DAMAGES ARISING OUT OF THE USE OR INABILITY TO  
USE THE PROGRAM (INCLUDING BUT NOT LIMITED TO  
LOSS OF DATA OR DATA BEING RENDERED INACCURATE  
OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR  
A FAILURE OF THE PROGRAM TO OPERATE WITH ANY  
OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER  
PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF  
SUCH DAMAGES.  
This section is intended to make thoroughly clear  
what is believed to be a consequence of the rest of this  
License.  
1. If the distribution and/or use of the Program is  
restricted in certain countries either by patents or by  
copyrighted interfaces, the original copyright holder  
who places the Program under this License may add an  
explicit geographical distribution limitation excluding  
those countries, so that distribution is permitted only  
in or among countries not thus excluded. In such case,  
this License incorporates the limitation as if written in  
the body of this License.  
END OF TERMS AND CONDITIONS  
END OF SCHEDULE 2  
2. The Free Software Foundation may publish revised  
and/or new versions of the General Public License  
from time to time. Such new versions will be similar in  
spirit to the present version, but may differ in detail to  
address new problems or concerns.  
Schedule 3  
If this Linksys product contains open source software  
licensed under the OpenSSL license:  
This product includes software developed by the  
OpenSSL Project for use in the OpenSSL Toolkit.  
Each version is given a distinguishing version number.  
If the Program specifies a version number of this  
License which applies to it and “any later version, you  
have the option of following the terms and conditions  
either of that version or of any later version published  
by the Free Software Foundation. If the Program does  
This product includes cryptographic software written by  
Eric Young ([email protected]).  
Wireless ADSL2+ Gateway  
28  
 
Software License Agreement  
Appendix E  
This product includes software written by Tim Hudson  
EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,  
BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE  
GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS;  
OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND  
ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,  
STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR  
OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF  
THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF  
SUCH DAMAGE.  
In addition, if this Linksys product contains open  
source software licensed under the OpenSSL license  
then the license terms below in this Schedule 3 will  
apply to that open source software. The license terms  
below in this Schedule 3 are from the public web site at  
The OpenSSL toolkit stays under a dual license, i.e. both  
the conditions of the OpenSSL License and the original  
SSLeay license apply to the toolkit. See below for the  
actual license texts. Actually both licenses are BSD-style  
Open Source licenses. In case of any license issues related  
to OpenSSL please contact [email protected].  
This product includes cryptographic software written by  
Eric Young ([email protected]). This product includes  
software written by Tim Hudson ([email protected]).  
Original SSLeay License  
Copyright © 1995-1998 EricYoung ([email protected])All  
rights reserved.  
OpenSSL License  
Copyright © 1998-2007 The OpenSSL Project. All rights  
reserved.  
This package is an SSL implementation written by Eric  
Young ([email protected]).  
Redistribution and use in source and binary forms, with  
or without modification, are permitted provided that the  
following conditions are met:  
The implementation was written so as to conform with  
Netscapes SSL.  
This library is free for commercial and non-commercial  
use as long as the following conditions are adhered to.  
The following conditions apply to all code found in this  
distribution, be it the RC4, RSA, lhash, DES, etc., code; not  
just the SSL code. The SSL documentation included with  
this distribution is covered by the same copyright terms  
except that the holder is Tim Hudson (tjh@cryptsoft.  
com).  
1. Redistributions of source code must retain the above  
copyright notice, this list of conditions and the  
following disclaimer.  
2. Redistributions in binary form must reproduce the  
above copyright notice, this list of conditions and the  
following disclaimer in the documentation and/or  
other materials provided with the distribution.  
Copyright remains Eric Young’s, and as such any Copyright  
notices in the code are not to be removed.  
3. All advertising materials mentioning features or  
use of this software must display the following  
acknowledgment: “This product includes software  
developed by the OpenSSL Project for use in the  
OpenSSL Toolkit. (http://www.openssl.org/)”  
If this package is used in a product, Eric Young should be  
given attribution as the author of the parts of the library  
used. This can be in the form of a textual message at  
program startup or in documentation (online or textual)  
provided with the package.  
4. The names “OpenSSL Toolkit” and “OpenSSL Project”  
must not be used to endorse or promote products  
derived from this software without prior written  
permission. For written permission, please contact  
Redistribution and use in source and binary forms, with  
or without modification, are permitted provided that the  
following conditions are met:  
5. Products derived from this software may not be called  
“OpenSSLnor may “OpenSSLappear in their names  
without prior written permission of the OpenSSL  
Project.  
1. Redistributions of source code must retain the  
copyright notice, this list of conditions and the  
following disclaimer.  
2. Redistributions in binary form must reproduce the  
above copyright notice, this list of conditions and the  
following disclaimer in the documentation and/or  
other materials provided with the distribution.  
6. Redistributions of any form whatsoever must retain  
the following acknowledgment:“This product includes  
software developed by the OpenSSL Project for use in  
the OpenSSL Toolkit (http://www.openssl.org/)”  
3. All advertising materials mentioning features or  
use of this software must display the following  
acknowledgement:  
THIS SOFTWARE IS PROVIDED BY THE OpenSSL PROJECT  
``AS IS’’ AND ANY EXPRESSED OR IMPLIED WARRANTIES,  
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED  
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR  
A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT  
SHALL THE OpenSSL PROJECT OR ITS CONTRIBUTORS BE  
LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,  
“This product includes cryptographic software written  
by Eric Young ([email protected])”  
Wireless ADSL2+ Gateway  
29  
 
Software License Agreement  
Appendix E  
The word ‘cryptographic’ can be left out if the routines  
from the library being used are not cryptographic  
related.  
1. IfyouincludeanyWindowsspecificcode(oraderivative  
thereof) from the apps directory (application code)  
you must include an acknowledgement:“This product  
includes software written by Tim Hudson (tjh@  
cryptsoft.com)”  
THIS SOFTWARE IS PROVIDED BY ERIC YOUNG ``AS IS’’  
AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING,  
BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF  
MERCHANTABILITY AND FITNESS FOR A PARTICULAR  
PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE  
AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY  
DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY,  
OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT  
LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR  
SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS  
INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY  
OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,  
OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)  
ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,  
EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.  
Thelicenseanddistributiontermsforanypubliclyavailable  
version or derivative of this code cannot be changed. i.e.  
this code cannot simply be copied and put under another  
distribution license [including the GNU Public License.]  
END OF SCHEDULE 3  
8032010NC-ST  
Wireless ADSL2+ Gateway  
30  
 

Kyocera All in One Printer 4500i User Manual
La Crosse Technology Weather Radio 308 2316 User Manual
Lanier Printer Accessories 117 0154 User Manual
LevelOne Network Router WBR 3407 User Manual
LST Smoke Alarm AMS 58000 700 User Manual
Magnavox Clock Radio mcr140 User Manual
Makita Pole Saw EK6100 User Manual
Melissa Electric Shaver 638 132 User Manual
Melissa Toaster 243 001 User Manual
Micro Innovations Digital Camera Micro Webcam Matrix User Manual