Magnepan Speaker Magneplanar CC3 User Manual

MAGNEPLANAR® CC3  
Instruction Manual  
White Bear Lake, Minnesota  
 
1.  
INTRODUCTION / GENERAL DESCRIPTION  
Congratulations on your purchase of the Magneplanar® CC3 Center Channel  
Loudspeaker. The Magneplanar CC3 was conceived and designed for perfectionists.  
The CC3 consists of a curved, two-way planar magnetic driver. Due to the elegant  
simplicity and ruggedness of the design, the Magneplanar CC3 Center Channel will  
give many years of trouble-free service.  
2.  
CARTON CONTENTS  
1 - CC3 Center Channel Loudspeaker  
1 - 1 Ohm Resistor  
1 - 4 Amp Normal Blow Fuse  
1 - Hex Wrench  
1 - Speaker Logo  
1 - Owner's Manual  
3.  
4.  
PACKAGING  
Save all packaging. If you ever need to ship the CC3 it can be shipped safely only in  
the original packaging. Should you discard it, packaging is available from Magnepan.  
HOOKUP  
The CC3 employs a unique, high-current connector. To install speaker cable, simply  
strip approximately ¼-inch of insulation from the speaker cable end, insert the cable  
tighten the set screw. Cables terminated with banana plugs or pins may also be used.  
For cables terminated with spade lugs, spade lug adapters are available from your  
Magneplanar dealer.  
Proper phasing is critical in obtaining good performance from your home  
theater system. Double check all of your connections to be certain the left, right, and  
center speakers are all connected in phase. The left, right, and center speakers are  
usually placed equal distance to the listener for correct time alignment.  
5.  
INSTALLATION AND PLACEMENT  
 
A)  
GENERAL  
The CC3 is designed for use on top of a TV, in or on top of a cabinet. For free-  
standing applications where the CC3 will be set on a speaker stand, call  
Magnepan for special instructions for this type of installation.  
The CC3 may be placed on top of a TV monitor as shown in Figure A. Magnetic  
shielding is not required. To achieve the smoothest vertical response, rotate the  
adjustment feet located on the bottom of the speaker. Adjust until the CC3 is  
aimed approximately at the listener's head, as shown in Figure A.  
FIGURE A  
B)  
INSTALLATION IN A CABINET  
The CC3 may be placed above or below the TV monitor in a cabinet. If the CC3  
is placed in an enclosed part of the cabinet, a space of 12" or more is required  
behind the CC3 for damping material. A special damping material is required,  
which is available from Magnepan for a small charge.  
Starting at the rear of the cabinet, LOOSELY pack insulation in the cavity behind  
the CC3. Leave an empty space of about 6 inches between the rear of the CC3  
and the insulation.  
If the speaker is placed below the TV or screen, the speaker can be tilted  
upward by removing the 2 existing adjustable feet. Locate the front T nut shown  
in the following diagrams. Use a hot soldering iron to burn a hole in the fabric to  
allow installation of an adjustable foot in the front T nut.  
Whenever possible, the rear of the cabinet should be vented or left open to  
allow the rear wave from the CC3 to escape.  
Again, for the smoothest response, tilt the speaker to aim it approximately at the  
listener's head as shown in Figure A.  
 
C)  
D)  
INSTALLATION USING BUILT-IN “T” NUTS  
As shown below, there are 3 “T” nuts built into the top and bottom of the CC3, at  
the designated locations. These built-in T nuts allow hanging or any other type  
of installation you may devise. CAREFULLY burn a hole in the cloth with a hot  
soldering tip or a method that will seal the hole in the cloth. Eye-bolts or hooks  
may be installed in the built-in nuts, and use ¼-inch X 20-inch threads.  
DAMPING  
When the CC3 is placed close to a rear wall, the sound quality can usually be  
improved with a damping material, such as a wall hanging, behind the speaker.  
6.  
PROCESSOR SETTINGS  
Set the processor center channel for “small” center channel speaker. If your processor  
provides variable crossover points for “small” center channel speaker, try crossover  
points between 100-200 Hz. Set the processor for “large” left/right speakers (if you  
have Magneplanar on-wall speakers, such as MMG Ws or MC1s, set the processor for  
“small” left/right speakers.  
Set the processor for “no subwoofer”. Even if you are using a subwoofer, you will get  
better performance from your MMG C by using the “no subwoofer” setting on the  
processor. If you want an explanation for this unusual set up procedure, please call  
Magnepan.  
Connect your subwoofer to the left/right preamp outputs of your receiver or processor.  
Set the subwoofer crossover points to the lowest frequency setting. Move the  
crossover point slowly to a higher frequency as you are listening to music. When the  
subwoofer overlaps with the Magneplanar, the bass will become “muddy”. When this  
happens, lower the crossover point.  
7.  
8.  
AMPLIFICATION  
WARNING: The CC3 is a 4 ohm speaker. Be certain the amplifier or receiver you are  
using is capable of driving a 4 ohm load. If you are uncertain, call the manufacturer of  
the amplifier.  
OPTIONAL TWEETER ATTENUATION  
The CC3 is provided with the means to reduce the output level of the tweeter section.  
If the surrounding walls of the listening room are exceptionally reflective, the overall  
perceived acoustical balance of the speaker will be tipped towards a “hot” high end.  
Attenuating the tweeter can help remedy this problem.  
 
Attenuation is accomplished by insertion of a simple, non-inductive resistor in series  
with the tweeter (see Figure B). Replace the jumper with the appropriate resistor to  
obtain the desired tweeter attenuation (typically 1 ohm for most rooms). The 1 ohm  
resistor provided will attenuate the tweeter 1 - 2dB. Other values are available from  
your Magneplanar dealer.  
Figure B  
9.  
SERVICE AND SHIPPING  
In the unlikely event you should need service for your CC3 Loudspeaker, we  
recommend you return it through your dealer. He is experienced in providing service  
and can assist you if the speaker must be returned to the factory. If you determine you  
need to return it directly to Magnepan, ship the speaker freight prepaid to:  
Magnepan, Incorporated  
1645 Ninth Street  
White Bear Lake, MN 55110  
Include a note describing the nature of the problem. Please include your name,  
address, and a daytime telephone number.  
 
10.  
SPECIFICATIONS  
System Description:  
Curved, two-way planar magnetic dipole loudspeaker  
155 Sq. In.  
Midrange Radiating Area:  
Quasi Ribbon Tweeter Size: 31" x 2-1/2"  
Frequency Response:  
Recommended Power:  
80Hz to 20kHz +/- 3dB  
See FAQ on web site at  
Sensitivity:  
86dB/500Hz/2.83V  
4 Ohms  
Impedance:  
Crossover Frequency:  
Dimensions:  
900Hz  
36"W X 10-1/2"H X 5-1/2"D  
20lbs./pair  
Shipping Weight:  
Warranty:  
Limited 3-Year to Original Owner  
11.  
CC3 PACKING LIST  
1 HEX WRENCH  
1 - 4 AMP FUSE  
1 - 1 OHM RESISTOR  
1 OWNERS MANUAL  
1 THANK YOU LETTER  
1 ADJUSTABLE FOOT  
1 SPEAKER EMBLEM  
 

Kyocera Digital Camera SL300R User Manual
Life Fitness Treadmill 90C User Manual
Lincoln Electric Welder 305D User Manual
LST Smoke Alarm HT 11005 User Manual
Macally Computer Drive IEEE 1394A User Manual
Manfrotto Carrying Case MBAG100P User Manual
Manitowoc Ice Ice Maker 7622073 User Manual
Metra Electronics Ventilation Hood 95 7868B User Manual
Metrologic Instruments Barcode Reader MS9590i User Manual
MGE UPS Systems Power Supply Nova 1100 AVR User Manual