McCulloch Trimmer 115376727 User Manual

Please do not return product to retailer.  
Por favor, no devuelva el producto al lugar de compra.  
Veuillez ne pas retourner le produit au détaillant.  
1--800--554--6723  
Register your product online at:  
Registre su producto en línea en:  
Enregistrez votre produit en ligne à l’adresse :  
Instruction Manual  
Manual de Instrucciones  
Manuel d’Instructions  
For Occasional Use Only  
WARNING:  
Read and follow all Safety Rules andOperating Instructionsbefore  
using this product. Failure to do so can result in serious injury.  
ADVERTENCIA:  
Lea el manual de instrucciones y siga todas las advertencias  
e instrucciones de seguridad. El no hacerlo puede resultar en  
lesiones graves.  
AVERTISSEMENT:  
Lire le manuel d’instructions et bien respecter tous les avertisse-  
ments et toutes les instructions de sécurité. Tout défaut de le faire  
pourrait entraîner des blessures graves.  
McCulloch  
9335 Harris Corners  
Charlotte, NC 28269  
McCulloch  
850 Matheson Blvd. West  
Mississauga, Ontario L5V 0B4  
115376727 Rev. 1 5/1/10 BRW  
 
IDENTIFICATION OF SAFETY SYMBOLS  
Never allow children to operate this unit.  
Store unit indoors in a high, dry place out of the reach of  
children.  
When servicing unit, use only identical replacement  
parts.  
Always stop unit and disconnect spark plug before clean-  
ing or servicing.  
WARNING: Fire hazard. Never mix, pour, or store gasoline or  
use the unit near a flame or sparks (including smoking, open flames, or  
work that can cause sparks).  
Use unleaded gasoline and two--stroke oil mixed at a ratio of  
40:1 (2.5%).  
3
 
OPTIONAL ATTACHMENTS  
These attachments used in combination with the specified powerhead have been evaluated  
to ANSI B175.3--2003, “Grass Trimmers and Brushcutters -- Safety Requirements”.  
Cutting attachment / guard,  
part no.  
Powerhead model Attachments  
Type  
Trimmer head  
MC025  
TNG 7  
537419214 / 530071824  
952711610  
Brushcutter attachment PP4000C  
These attachments used in combination with the specified powerhead have been evaluated  
to applicable ISO-- and EN safety requirement standards by the Swedish Machinery Testing  
Institute:  
Attachments  
Type  
Part no.  
Edger attachment  
Cultivator attachment  
Blower attachment  
Pruner attachment  
PP1000E  
PP2000T  
PP3000B  
PP5000P  
952711607  
952711608  
952711609  
952711612  
SAFETY RULES  
S Always wear face or dust mask if operation  
is dusty.  
WARNING: When using gardening  
appliances, basic safety precautions must al-  
ways be followed to reduce the risk of fire and  
serious injury. Read and follow all instructions.  
This power unit can be dangerous! Operator  
is responsible for following instructions and  
warnings on unit and in manual. Read entire  
instruction manual before using unit! Be thor-  
oughly familiar with the controls and the prop-  
er use of the unit. Restrict the use of this unit  
to persons who have read, understand, and  
will follow the instructions and warnings on  
the unit and in the manual. Never allow chil-  
dren to operate this unit.  
S Always wear heavy, long pants, long  
sleeves, boots, and gloves. Wearingsafety  
leg guards is recommended.  
S Always wear foot protection. Do not go  
barefoot or wear sandals. Stay clear of  
spinning line.  
S Secure hair above shoulder length. Secure  
or remove loose clothing or clothing with  
loosely hanging ties, straps, tassels, etc.  
They can be caught in moving parts.  
S Being fully covered also helps protect you  
from debris and pieces of toxic plants  
thrown by spinning line.  
S Stay Alert. Do not operate this unit when you  
are tired, ill, upset or under the influence of al-  
cohol, drugs, or medication. Watch what you  
are doing; use common sense.  
S Wear hearing protection.  
INSTRUCTION  
MANUAL  
SAFETY INFORMATION  
ON THE UNIT  
S Never start or run inside a closed room or  
building. Breathing exhaust fumes can kill.  
S Keep handles free of oil and fuel.  
S Always keep engine on the right hand side  
of your body.  
DANGER: Never use blades withline  
trimmer attachment. Never use flailing de-  
vices with any attachment. This unit (when  
used withsupplied linetrimmer attachment) is  
designed for line trimmer use only. Use of any  
other accessories with line trimmer attach-  
ment will increase the risk of injury.  
If situations occur which are not covered in  
this manual, use care and good judgment. If  
you needassistance, contact your authorized  
service dealer or call 1-800-554-6723.  
S Hold the unit firmly with both hands.  
S Keep trimmer head (or other optional at-  
tachment) below waist level and away from  
all parts of your body. Do not raise engine  
above your waist.  
S Keep all parts of your body away from muf-  
fler and spinning line (or other optional at-  
tachment). Keep engine below waist level.  
A hot muffler can cause serious burns.  
S Keep firm footing and balance. Do not over-  
reach or use from unstable surfaces such as  
ladders, trees, steep slopes, rooftops, etc.  
S Use only in daylight or good artificial light.  
S Use only for jobs explained in this manual  
(or manuals for optional attachments).  
OPERATOR SAFETY  
S Dress properly. Always wear safety  
glasses or similar eye protection when op-  
erating, or performing maintenance, on  
your unit (safety glasses are available).  
Eye protection should be marked Z87.  
4
 
hand tools could cause blood vessel or nerve  
damage in the fingers, hands, and joints of  
people prone to circulation disorders or abnor-  
mal swellings. Prolonged use in cold weather  
has been linked to blood vessel damage in  
otherwise healthy people. If symptoms occur  
such as numbness, pain, loss of strength,  
change in skin color or texture, or loss of feeling  
in the fingers, hands, or joints, discontinue the  
use of this tool and seek medical attention. An  
anti--vibration system does not guarantee the  
avoidance of these problems. Users who oper-  
ate power tools on a continual and regular basis  
must monitor closely their physical condition  
and the condition of this tool.  
SPECIAL NOTICE: This unit is equipped  
with a temperature limiting muffler and spark  
arresting screen which meets the require-  
ments of California Codes 4442 and 4443. All  
U.S. forest land and the states of California,  
Idaho, Maine, Minnesota, New Jersey, Ore-  
gon, and Washington require by law that  
many internal combustion engines be  
equipped witha spark arresting screen. If you  
operatein alocalewhere such regulations ex-  
ist, you are legally responsible for maintaining  
the operating condition of these parts. Failure  
to do so is a violation of the law. For normal  
homeowner use, the muffler and spark arrest-  
ing screen will not require any service. After  
50 hours of use, we recommend that your  
muffler be serviced or replaced by an autho-  
rized service dealer.  
UNIT / MAINTENANCE SAFETY  
WARNING: Disconnect the spark  
plug before performing maintenance except  
carburetor adjustments.  
S Look for and replace damaged or loose  
parts before each use. Look for and repair  
fuel leaks before use. Keepin good working  
condition.  
S Replace trimmer head parts that are  
chipped, cracked, broken, or damaged in  
any other way before using the unit.  
S Maintain unit according to recommended pro-  
cedures. Keep cutting line at proper length.  
S Use only 0.080(2 mm) diameter line. Never  
use wire, rope, string, etc.  
S Install required shield properly before using  
the unit. Use only specified trimmer head;  
make sure it is properly installed and se-  
curely fastened.  
S Make sure unit is assembled correctly as  
shown in this manual.  
S Make carburetor adjustments with lower  
end supported to prevent line from contact-  
ing any object.  
S Keep others away when making carburetor  
adjustments.  
S Use only recommended McCulloch acces-  
sories and replacement parts.  
S Have all maintenance and service not ex-  
plained in this manual performed by an au-  
thorized service dealer.  
FUEL SAFETY  
LINE TRIMMER SAFETY  
S Mix and pour fuel outdoors.  
S Keep away from sparks or flames.  
S Use a container approved for fuel.  
S Do not smoke or allow smoking near fuel or  
the unit.  
WARNING: Inspect the area to be  
trimmed before each use. Remove objects  
(rocks, broken glass, nails, wire, etc.) which  
can be thrown by or becomeentangled inline.  
Hard objects can damage the trimmer head  
and be thrown causing serious injury.  
S Keep others including children, animals,  
bystanders, and helpers at least 50 feet (15  
meters) away. Bystanders should be encour-  
aged to wear safety glasses. Stop engine  
immediately if you are approached.  
S Use only for trimming, scalping, mowing and  
sweeping. Do not use for edging, pruning or  
hedge trimming.  
S Cut from your right to your left. Cutting on  
left side of the shield will throw debris away  
from the operator.  
S Avoid spilling fuel or oil. Wipe up all fuel  
spills.  
S Move at least 10 feet (3 meters) away from  
fueling site before starting engine.  
S Stop engine and allow to cool before re-  
moving fuel cap.  
S Always store gasoline in a container ap-  
proved for flammable liquids.  
TRANSPORTING AND STORAGE  
S Allow engine to cool before storing or trans-  
porting in vehicle.  
S Empty the fuel tank before storing or trans-  
porting the unit. Use up fuel left in thecarbu-  
retor by starting the engine and letting it run  
until it stops.  
ADDITIONAL SAFETY RULES  
FOR OPTIONAL ATTACHMENTS  
S Store unit and fuel in area where fuel vapors  
cannot reach sparks or open flames from wa-  
ter heaters, electric motors or switches, fur-  
naces, etc.  
WARNING: For each optional attach-  
ment used, read entire instruction manual be-  
fore use and follow all warnings and instructions  
in manual and on attachment.  
S Store unit so line limiter blade cannot acci-  
dentally cause injury. The unit can be hung  
by the shaft.  
S Store unit out of reach of children.  
WARNING: Ensure handlebar is  
installed when using brushcutter attachment.  
Attach handlebar above arrow on safety label  
on the upper shaft (engine end of unit). If your  
brushcutter attachment does not include a  
WARNING: The engine exhaust  
from this product contains chemicals known  
totheStateof California tocause cancer, birth  
defects or other reproductive harm.  
handlebar,  
a
handlebar accessory kit  
SAFETY NOTICE: Exposure to vibrations  
(#530071451) is available from your autho-  
rized service dealer.  
through prolonged use of gasoline powered  
5
 
S Never run unit without the proper equip-  
ment attached. When using your unit as a  
blower, always install blower tubes.  
S Check air intake opening, blower tubes or  
vacuum tubes frequently, always with en-  
gine stopped and spark plug disconnected.  
Keep vents and discharge tubes free of de-  
bris which can accumulate and restrict  
proper air flow.  
S Never place any object inair intake opening  
as this could restrict proper air flow and  
cause damage to the unit.  
EDGER SAFETY  
S Never use for spreading chemicals, fertiliz-  
ers, or other substances which may contain  
toxic materials.  
S To avoid spreading fire, do not use near leaf  
or brush fires, fireplaces, barbecue pits,  
ashtrays, etc.  
WARNING: Inspect the area to be  
edged before each use. Remove objects  
(rocks, broken glass, nails, wire, etc.) which  
can be thrown by the blade or can wrap  
around the shaft.  
BRUSHCUTTER SAFETY  
WARNING: Blade rotates momen-  
tarily after the trigger is released or engine is  
turned off. The blade can seriously cut you or  
others. Allow blade to stop before removing it  
from the cut.  
DANGER: Blade can thrust violently  
away from material it does not cut. Blade  
thrust can cause amputation of arms or legs.  
WARNING: Do not use trimmer head  
as a fastening device for the blade.  
S Throw away blades that are bent, warped,  
cracked, broken or damaged in any other  
way. Replace parts that are cracked,  
chipped, or damaged before using the unit.  
S Do not attempt to remove cut material nor  
hold material to be cut when the engine is  
running or when cutting blade is moving.  
S Always keep the wheel and depth adjusting  
skid in contact with the ground.  
S Always push the unit slowly over the  
ground. Stay alert for uneven sidewalks,  
holes in the terrain, large roots, etc.  
WARNING: The blade continues to  
spin after the trigger is released or engine is  
turned off. The coasting blade can throw ob-  
jects or seriously cut you if accidentally  
touched. Stop the blade by contacting the  
right hand side of the coasting blade with ma-  
terial already cut.  
BLOWER/VACUUM SAFETY  
WARNING:  
Inspect area before  
starting unit. Remove all debris and hard ob-  
jects such as rocks, glass, wire, etc. that can  
ricochet, be thrown, or otherwise cause injury  
or damage during operation.  
S Do not set unit on any surface except a  
clean, hard area while engine is running.  
Debris such as gravel, sand, dust, grass,  
etc., could be picked up by the air intake  
and thrown out through discharge opening,  
damaging unit, property, or causing serious  
injury to bystanders or operator.  
S Never place objects inside the blower tubes,  
vacuum tubes or blower outlet. Always direct  
the blowing debris away from people, ani-  
mals, glass, and solid objects such as trees,  
automobiles, walls, etc. The force of air can  
cause rocks, dirt, or sticks to be thrown or to  
ricochet which can hurt people or animals,  
break glass, or cause other damage.  
WARNING: Inspect the area to be  
cut before each use. Remove objects (rocks,  
broken glass, nails, wire, etc.) which can be  
thrown or become entangled in the blade or  
trimmer line.  
6
 
S Throw away and replace blades that are  
bent, warped, cracked, broken or damaged  
in any other way.  
HEDGE TRIMMER SAFETY  
DANGER: RISK OF CUT; KEEP  
HANDS AWAY FROM BLADE -- Blade moves  
momentarily after the trigger is released or en-  
gine is turned off. Do not attempt to clear away  
cut material when the blade is in motion. Make  
sure engine is turned off, the spark plug wire is  
disconnected, and the blade has stopped mov-  
ing before removing jammed material from the  
cutting blade. Do not grab or hold the unit by the  
cutting blade.  
S Install required shield properly before using  
the unit. Use the metal shield for all metal  
blade use.  
WARNING: Only use brushcutter at-  
tachments that provide a metal shield with  
proboscis nose.  
Proboscis  
nose  
S Use only specified bladeand make sure it is  
properly installed and securely fastened.  
S Cut from your left to your right. Cutting on  
the right side of the shield will throw debris  
away from the operator.  
S Always use the handlebar and a properly  
adjusted shoulder strap with blade (see AS-  
SEMBLY instructions in brushcutter attach-  
ment instruction manual).  
WARNING: Inspect the area before  
starting the unit. Remove all debris and hard  
objects such as rocks, glass, wire, etc. that  
can ricochet, be thrown, or otherwise cause  
injury or damage during operation.  
CULTIVATOR SAFETY  
WARNING: Rotating tines can cause  
serious injury. Keep away from rotating tines.  
Stop the engine and disconnect the spark plug  
before unclogging tines or making repairs.  
S Do not use a cutting blade that is bent,  
warped, cracked, broken or damaged in any  
other way. Have worn or damaged parts re-  
placed by your authorized service dealer.  
S Always keep unit in front of your body.  
Keep all parts of your body away from the  
cutting blade.  
S Keep the cutting blade and air vents clear of  
debris.  
POLE PRUNER SAFETY  
WARNING: The reciprocating blade/  
rotating chain can cause severe injury. In-  
spect the unit before use. Do not operate unit  
with a bent, cracked or dull bladeor dull chain.  
Keep away from the blade/chain.  
WARNING: Inspect the area to be  
cultivated before starting the unit. Removeall  
debris and hard and sharp objects such as  
rocks, vines, branches, rope, string, etc.  
S Avoid heavy contact with solid objects that  
might stop the tines. If heavy contact oc-  
curs, stop the engine and inspect the unit  
for damage.  
S Never operate the cultivator without the tine  
cover in place and properly secured.  
S Keep the tines and guard clear of debris.  
S After striking a foreign object, stop the en-  
gine, disconnect the spark plug and inspect  
the cultivator for damage. Repair before re-  
starting.  
S Disconnect attachment from the drive en-  
gine before cleaning the tines with a hose  
and water to remove any build--up. Oil the  
tines to prevent rust.  
WARNING: The reciprocating blade/  
rotating chain is sharp. Do not touch. To pre-  
vent serious injury, always stop engine and  
ensure blade/chain has stopped moving, dis-  
connect spark plug, and wear gloves when  
changing or handling the blade or chain.  
WARNING: A coasting blade/rotat-  
ing chain cancauseinjury whileit continues to  
move after the engine is stopped. Maintain  
proper control of the unit until the blade/chain  
has completely stopped moving. Keep  
hands, face and feet at a distance from all  
moving parts. Do not attempt to touch or stop  
the blade or chain when it is moving.  
S Always wear gloves when servicing or  
cleaning the tines. The tines become very  
sharp from use.  
S Do not run unit at high speed unless culti-  
vating.  
7
 
WARNING:  
Falling objects can  
WARNING: Never lean over dis-  
charge chute. Rocks or debris could be  
thrown into the eyes and face and cause seri-  
ous injury or blindness.  
cause severe head injury. Wear head protec-  
tion when operating this unit with a pole prun-  
er attachment.  
WARNING: Inspect the area where  
the unit is to be used. Remove objects that  
could be thrown or damage the unit. Some  
objects may be hidden by fallen snow -- be  
alert for the possibility.  
S Direct material discharge away from glass  
enclosures, automobiles, etc.  
S Do not run engine at high speed while not  
removing snow.  
WARNING: To prevent serious inju-  
ry, do not use more than one boom extension  
with a pole pruner attachment.  
S Be attentive when using the snowthrower,  
and stay alert for holes in the terrain and  
other hidden hazards.  
WARNING: Keep the pruner away  
from power lines or electrical wires.  
S Only use for pruning limbs or branches up  
to 6 inches (15 cm) in diameter.  
S Do not operate the unit faster than the  
speed needed to prune. Do not run the unit  
at high speed when not pruning.  
S Always stop the unit when work is delayed  
or when walking from onecutting location to  
another.  
S If you strike or become entangledwith afor-  
eign object, stop the engine immediately  
and check for damage. Have any damage  
repaired by an authorized service dealer  
before attempting further operations. Dis-  
card blades that are bent, warped, cracked  
or broken.  
S Stop the unit immediately if you feel exces-  
sive vibration. Vibration is a sign of trouble.  
Inspect thoroughly for loose nuts, bolts or  
damage before continuing. Contact an au-  
thorized service dealer for repair or re-  
placement of affected parts as necessary.  
S Make sure the rotor will spin freely before at-  
taching the snowthrower to the powerhead.  
S If the rotor will not rotate freely due tofrozen  
ice, thaw the unit before thoroughly before  
attempting to operate under power.  
S Keep the rotor clear of debris.  
S Do not throw snow near other people. The  
snow thrower could propel small objects at  
high speed causing injury.  
S After striking a foreign object, stop the en-  
gine, disconnect spark plug and inspect the  
snowthrower for damage and repair if nec-  
essary before restarting unit.  
S Never operate the snowthrower near glass  
enclosures, automobiles and trucks.  
S Never attempt to use the snowthrower on a  
roof.  
S Never operate the snowthrower near win-  
dow wells, dropoffs, etc.  
S Never discharge snow onto public roads or  
near moving traffic.  
S Clear snow from slopes by going up and  
down; never across. Use caution when  
changing directions. Never clear snow from  
steep slopes.  
S Let snowthrower run for a few minutes after  
clearing snow so moving parts do not  
freeze.  
S Look behind and use care when backing  
up. Exercise caution to avoidslipping or fal-  
ling, especially when operating in reverse.  
S Know how to stop quickly.  
SNOW THROWER SAFETY  
WARNING: Keep hands and feet  
away from the rotor when starting or running  
the engine. Never attempt to clear the rotor  
with the engine/motor running. Stop engine  
and disconnect spark plug before unclogging  
snow or debris from discharge chute or when  
adjusting vanes.  
8
 
ASSEMBLY  
WARNING: If received assembled,  
repeat all steps to ensure your unit is properly  
assembled and all fasteners are secure.  
Examine parts for damage. Do not use dam-  
aged parts.  
NOTE: If you need assistance or find parts  
missing or damaged, call 1-800-554-6723.  
It is normal for the fuel filter to rattle in the  
empty fuel tank.  
Locking/Release  
Button in Primary Hole  
Finding fuel or oil residue on muffler is normal  
due to carburetor adjustments and testing  
done by the manufacturer.  
INSTALLING TRIMMER ATTACH-  
MENT  
CAUTION: When installing trimmer attach-  
ment, place the unit on a flat surface for stability.  
1. Loosen the coupler by turning the knob  
counterclockwise.  
For assembly of optional attachments (see  
list on page 11), refer to the ASSEMBLY sec-  
tion of the applicable attachment instruction  
manual.  
Coupler  
ATTACHING SHIELD  
WARNING: The shield must be prop-  
erly installed. The shield provides partial protec-  
tion from the risk of thrown objects to the opera-  
tor and others and is equipped with a line limiter  
blade which cuts excess line to the proper  
length. The line limiter blade (on underside of  
shield) is sharp and can cut you. For proper  
orientation of shield, see KNOW YOUR TRIM-  
MER illustration in OPERATION section.  
Shipping  
protector  
EN  
Knob  
TIGHTEN  
1. Remove wing nut from shield.  
2. Insert bracket into slot as shown.  
3. Pivot shielduntil bolt passes through hole  
in bracket.  
2. Remove shipping protector from coupler.  
3. Remove the shaft cap from the trimmer  
attachment (if present).  
4. Position locking/release button of attach-  
ment into guide recess of coupler.  
5. Push the attachment into the coupler until  
the locking/release button snaps into the  
primary hole.  
4. Securely tighten wing nut onto bolt.  
Slot  
6. Before using theunit, tighten the knobse-  
curely by turning clockwise.  
Shield  
Bracket  
Wing  
Primary Hole  
Coupler  
Guide Recess  
Nut  
Locking/  
Line Limiter Blade  
Upper  
Shaft  
Attachment  
Release  
Button  
ADJUSTING THE ASSIST HANDLE  
WARNING: Make sure the locking/  
release button is locked in the primary hole  
and the knob is securely tightened before op-  
erating the unit. All attachments are designed  
to be used in the primary hole unless otherwise  
stated in the applicable attachment instruction  
manual. Using the wrong hole could lead to seri-  
ous injury or damage to the unit.  
WARNING: When adjusting the assist  
handle, be sure it remains above the safety label  
and below the mark or arrow on the shaft.  
1. Loosen wing nut on handle.  
2. Rotate the handle on the shaft to an up-  
right position; retighten wing nut.  
9
 
OPERATION  
KNOW YOUR TRIMMER  
READ THIS INSTRUCTION MANUAL AND SAFETY RULES BEFORE OPERATING YOUR UNIT.  
Compare the illustrations with your unit to familiarize yourself with the location of the various controls  
and adjustments. Save this manual for future reference.  
Muffler  
Assist Handle  
Tri
He
Throttle Trigger  
Primer Bulb  
Spark  
Plug  
Start  
Lever  
Line Limiter  
Blade  
ON/STOP  
Switch  
Starter handle  
ON/STOP SWITCH  
START LEVER  
The ON/STOP switch is located on the trigger  
handle and is used to stop the engine. To stop  
the engine, push and release the engine ON/  
STOP switch.  
The START LEVER helps to supply fuel to the  
engine to aid in starting. Activate the starting  
system by moving the start lever to the START  
position. DO NOT squeeze the throttle trigger  
until the engine has started and runs. After the  
engine starts, allow the engine to warm--up  
10--15 seconds, then fully squeeze the throttle  
trigger to deactivate the starting system.  
COUPLER  
PRIMER BULB  
The PRIMER BULB removes air from thecar-  
buretor and fuel lines and fills them with fuel.  
This allows you to start the engine with fewer  
pulls on the starter rope. Activate the primer  
bulb by pressing it and allowing it to return to  
its original form.  
The COUPLER enables optional attach-  
ments to be installed on the unit.  
gasoline. Pour the entire contents of the 3.2  
ounce (95 ml) container of oil into 1 gallon (4  
liters) of gasoline to achieve the proper fuel  
mixture. DO NOT USE automotive or marine  
oil. These oils will cause engine damage.  
When mixing fuel follow the instructions  
printed on the container. Once oil is added to  
gasoline, shake container momentarily to  
assure that the fuel is thoroughly mixed.  
Always read and follow the safety rules  
relating to fuel before fueling your unit.  
BEFORE STARTING ENGINE  
WARNING: Be sure to read the fuel  
information in the safety rules before you begin.  
If you do not understand the safety rules, do not  
attempt to fuel your unit. Call 1-800-554-6723.  
FUELING ENGINE  
WARNING: Remove fuel cap slowly  
when refueling.  
CAUTION: Never use straight gasoline in  
your unit. This will cause permanent engine  
damage and void the limited warranty.  
HELPFUL TIP  
To obtain the correct oil mix  
ratio, pour 3.2 ounces of  
2-cycle synthetic oil into  
one gallon of fresh gas.  
FUEL REQUIREMENTS  
This engine requires the use of minimum 87  
octane [R+M]/2 clean gasoline.  
This engine is certified to operate on  
unleaded gasoline. Before operation,  
gasoline must be mixed with a good quality  
synthetic 2-cycle air-cooled engine oil  
designed to be mixed at a ratio of 40:1. A 40:1  
ratio is obtained by mixing 3.2 fluid ounces (95  
ml) of oil with 1 gallon (4 liters) of unleaded  
IMPORTANT  
Use of alcohol blended fuels (called gasohol or  
using ethanol or methanol) can cause major en-  
gine performance and durability problems.  
10  
 
WARNING: Alternative fuels (not gas-  
oline) such as E--15 (15% alcohol), E--20 (20%  
alcohol), E--85 (85% alcohol) are NOT classified  
as gasoline and are NOT approved for use in  
2--stroke gasoline engines. Use of alternative  
fuels will cause problems such as: improper  
clutch engagements, overheating, vapor lock,  
power loss, lubrication deficiency, deterioration  
of fuel lines, gaskets and internal carburetor  
components, etc. Alternative fuels cause high  
moisture absorption into the fuel/oil mixture  
leading to oil and fuel separation.  
Primer Bulb  
HOW TO STOP YOUR UNIT  
Start Lever  
S Release the throttle trigger.  
S Push and release the engine ON/STOP  
switch. The switch will automatically return to  
the ON position. Wait 5 seconds before at-  
tempting to restart unit to allow switch to reset.  
Starter Handle  
HOW TO START YOUR UNIT  
4. Pull starter rope handle sharply until en-  
gine starts and runs.  
5. Allow unit to run for 10--15 seconds, then  
fully squeeze the throttle trigger to disen-  
gage the starting system.  
WARNING: Avoid any contact with  
the muffler. A hot muffler can cause serious  
burns.  
STARTING A WARM ENGINE  
1. Squeeze and hold the throttle trigger.  
Keep throttle trigger fully squeezed until  
engine runs smoothly.  
2. Pull starter rope sharply while squeezing  
throttle trigger until engine runs.  
Starting position  
NOTE: Normally, the warm starting proce-  
dure can be used within 5--10 minutes after  
the unit is turned off. If the unit sits for more  
than 10 minutes without being ran, it will be  
necessary to start the unit by following the  
steps under STARTING A COLD ENGINE or  
following the starting instruction steps shown  
on the unit.  
HELPFUL TIP  
If your engine still does not  
start after following these  
instructions, please call  
1-800-554 -6723.  
STARTING A FLOODED ENGINE  
Flooded engines can be started by placing the  
start lever to the RUN position. Fully squeeze  
throttle trigger. Pull the starter handle repeatedly  
while squeezing throttle trigger until engine  
starts and runs. This could require pulling the  
starter handle many times, depending on how  
badly the unit is flooded. If the unit still doesn’t  
start, refer to TROUBLESHOOTING TABLE or  
call 1-800-554-6723.  
STARTING A COLD ENGINE  
NOTE: DO NOT squeeze the throttle trigger  
until the engine has started and runs.  
1. Set unit on a flat surface.  
2. Slowly press the primer bulb 6 times.  
3. Move the start lever to the START posi-  
tion.  
OPERATING THE COUPLER  
This model is equipped with a coupler which  
enables optional attachments to be installed.  
The optional attachments are:  
MODEL:  
Edger . . . . . . . . . . . . . . . . . . . . . . PP1000E  
Cultivator . . . . . . . . . . . . . . . . . . . PP2000T  
Blower . . . . . . . . . . . . . . . . . . . . . PP3000B  
Brushcutter . . . . . . . . . . . . . . . . . PP4000C  
Pruner . . . . . . . . . . . . . . . . . . . . . PP5000P  
11  
 
WARNING: Always stop unit anddis-  
connect spark plug before removing or instal-  
ling attachments.  
REMOVING TRIMMER ATTACH-  
MENT (OR OTHER OPTIONAL AT-  
TACHMENTS)  
CAUTION: When removing or installing at-  
tachments, place the unit on a flat surface for  
stability.  
1. Loosen the coupler by turning the knob  
counterclockwise.  
Locking/Release  
Button in Primary Hole  
Coup
OPERATING INSTRUCTIONS  
It is recommended that the engine not be  
operated for longer than 1 minute at full  
throttle.  
Attachment  
SEN  
Knob  
OPERATING POSITION  
ALWAYS WEAR:  
Eye Protection  
TIGHTEN  
Long Pants  
2. Press and hold the locking/release button.  
Locking/Release  
Button  
Heavy Shoes  
Cut from your right to your left.  
Upper Shaft  
Attachment  
Coupler  
WARNING: Always wear eyeprotec-  
tion. Never lean over the trimmer head.  
Rocks or debris canricochet or be throwninto  
eyes and face and cause blindness or other  
serious injury.  
Do not run the engine at a higher speed than  
necessary. The cutting line will cut efficiently  
whenthe engineis runat less than full throttle.  
At lower speeds, there is less engine noise and  
vibration. The cutting line will last longer and will  
be less likely to “weld” onto the spool.  
Always release the throttle trigger and allow the  
engine to return to idle speed when not cutting.  
To stop engine:  
S Release the throttle trigger.  
S Push and release the engine ON/STOP  
switch.  
3. While securely holding the engine and  
upper shaft, pull the attachment straight  
out of the coupler.  
INSTALLING OPTIONAL ATTACH-  
MENTS  
1. Remove the shaft cap from the attach-  
ment (if present).  
2. Position locking/release button of attach-  
ment into guide recess of coupler.  
3. Push the attachment into the coupler until  
the locking/release button snaps into the  
primary hole.  
4. Before using theunit, tighten the knobse-  
curely by turning clockwise.  
Primary Hole  
Coupler  
Guide Recess  
TRIMMER LINE ADVANCE  
Thetrimmer line willadvance approximately 2  
inches (5 cm) each time the bottom of the  
trimmer head is tapped on the ground with the  
engine running at full throttle.  
Locking/  
Release  
Button  
Upper  
Shaft  
Attachment  
The most efficient line length is the maximum  
length allowed by the line limiter.  
Always keep the shield in place when the tool  
is being operated.  
WARNING: Make sure the locking/  
release button is locked in the primary hole  
and the knob is securely tightened before op-  
erating the unit. All attachments are designed  
to be used in the primary hole unless otherwise  
stated in the applicable attachment instruction  
manual. Using the wrong hole could lead to seri-  
ous injury or damage to the unit.  
To advance line:  
S Operate the engine at full throttle.  
S Hold the trimmer head parallelto and above  
the grassy area.  
S Tap the bottom of the trimmer head lightly on  
the ground one time. Approximately 2 inches  
(5 cm) of line will be advanced with each tap.  
12  
 
Always tap the trimmer head on a grassy  
area. Tapping on surfaces such as concrete  
or asphalt can cause excessive wear to the  
trimmer head.  
Trimming  
If the line is worn down to 2 inches (5 cm) or  
less, more than one tap will be required to ob-  
tain the most efficient line length.  
3 inches (8 cm)  
above ground  
WARNING: Use only 0.080(2 mm)  
diameter line. Other sizes of line will not ad-  
vance properly and can cause serious injury.  
Do not use other materials such as wire,  
string, rope, etc. Wire can break off during  
cutting and become a dangerous missile that  
can cause serious injury.  
SCALPING -- The scalping technique re-  
moves unwanted vegetation down to the  
ground. Hold the bottom of the trimmer head  
about 3 inches (8 cm) above the ground and  
at an angle. Allow the tip of the lineto strikethe  
ground around trees, posts, monuments, etc.  
This technique increases line wear.  
CUTTING METHODS  
WARNING: Use minimum speed  
and do not crowdthe linewhen cutting around  
hard objects (rock, gravel, fence posts, etc.),  
whichcan damage thetrimmer head, become  
entangled in the line, or be thrown causing a  
serious hazard.  
Scalping  
S The tip of the line does the cutting. You will  
achieve the best performance and  
minimum line wear by not crowding the line  
into the cutting area. The right and wrong  
ways are shown below.  
MOWING -- Your trimmer is ideal for mowing  
in places conventional lawn mowers cannot  
reach. In the mowing position, keep the line  
parallel to the ground. Avoid pressing the  
head into the ground as this can scalp the  
ground and damage the tool.  
Tip of the Line  
Line Crowded Into  
Work Area  
Does The Cutting  
Mowing  
Right  
Wrong  
S The line will easily remove grass and  
weeds fromaround walls, fences, trees and  
flower beds, but it also can cut the tender  
bark of trees or shrubs and scar fences.  
S For trimming or scalping, use less than full  
throttle to increase line life and decrease head  
wear, especially:  
SWEEPING -- The fanning action of the rotat-  
ing line can be used for a quick and easy  
clean up. Keep the line parallel to and above  
the surfaces being swept and move the tool  
from side to side.  
S During light duty cutting.  
S Near objects around which the line can  
wrap such as small posts, trees or fence  
wire.  
Swee
S For mowing or sweeping, use full throttle for  
a good clean job.  
TRIMMING -- Hold the bottom of the trimmer  
head about 3 inches (8 cm) above the ground  
and at an angle. Allow only the tip of the line to  
make contact. Do not force trimmer line into  
work area.  
13  
 
MAINTENANCE  
1. Clean the cover and the area around it to  
keep dirt from falling into the carburetor  
chamber when the cover is removed.  
2. Remove parts by pressing button to re-  
lease air filter cover.  
WARNING: Disconnect the spark  
plug before performing maintenance except  
for carburetor adjustments.  
HELPFUL TIP  
NOTE: To avoid creating a fire hazard or  
producing harmful evaporative emissions, do  
not clean filter in gasoline or other flammable  
solvent.  
3. Wash the filter in soap and water.  
4. Allow filter to dry.  
5. Replace parts.  
IMPORTANT: Have all  
repairs other than the rec-  
ommended maintenance  
described in the instruction  
manual performed by an  
authorized service dealer.  
If any dealer other than an authorized  
service dealer performs work on the  
product, we may not pay for repairs un-  
der warranty. It is your responsibility to  
maintain and perform general mainte-  
nance.  
Button  
Air Filter  
CHECK FOR LOOSE  
FASTENERS AND PARTS  
S Spark Plug Boot  
ir Filter Cover  
S Air Filter  
S Housing Screws  
S Assist Handle Screw  
S Debris Shield  
CHECK FOR DAMAGED OR  
WORN PARTS  
Contact an authorized service dealer for re-  
placement of damaged or worn parts.  
S ON/STOP Switch -- Ensure ON/STOP  
switch functions properly by pushing and  
releasing the switch. Make sure engine  
stops. Wait 5 seconds before attempting to  
restart unit to allow switch to reset. Restart  
engine and continue.  
S Fuel Tank -- Discontinue use of unit if fuel  
tank shows signs of damage or leaks.  
S Debris Shield -- Discontinue use of unit if  
debris shield is damaged.  
MUFFLER AND SPARK ARREST-  
ING SCREEN  
WARNING: The muffler on this prod-  
uct contains chemicals known to the State of  
California to cause cancer.  
As your unit is used, carbon deposits build up  
on the muffler and spark arresting screen.  
For normal homeowner use, however, the  
muffler and spark arresting screen will not re-  
quire any service. After 50 hours of use, we  
recommend that your muffler be serviced or  
replaced by your authorized service dealer.  
REPLACE SPARK PLUG  
Replace the spark plug each year to ensure  
the engine starts easier and runs better. Set  
spark plug gap at 0.025 inch (0.6 mm). Igni-  
tion timing is fixed and nonadjustable.  
NOTE: This spark ignition system complies  
with the Canadian standard ICES--002.  
1. Twist, then pull off spark plug boot.  
2. Remove spark plug from cylinder and  
discard.  
INSPECT AND CLEAN UNIT AND  
LABELS  
S After each use, inspect complete unit for  
loose or damaged parts. Clean the unit and  
labels using a damp cloth with a mild deter-  
gent.  
S Wipe off unit with a clean dry cloth.  
CLEAN AIR FILTER  
A dirty air filter decreases engine perform-  
ance and increases fuel consumption and  
harmful emissions. Always clean after every  
5 hours of operation.  
3. Replace with Champion RCJ-6Y spark  
plug and tighten securely with a 3/4 inch  
(19 mm) socket wrench.  
4. Reinstall the spark plug boot.  
14  
 
SERVICE AND ADJUSTMENTS  
5. When installing new line on an existing  
REPLACING THE LINE  
spool, hold the spool as shown.  
6. Bend the line at the midpoint and insert  
the bend into the slot in the center rim of  
the spool. Ensure line snaps into position  
in the slot.  
1. Press the tabs on the side of the trimmer  
head and remove cover and spool.  
7. With your finger between the lines, wrap  
the lines evenly and firmly around the  
spool in a clockwise direction.  
Tab  
Tab  
Cover  
Spool  
8. Position the lines in the guide slots.  
Guide slot  
Guide slot  
2. Remove any remaining line.  
3. Clean dirt and debris from all parts. Re-  
place spool if it is worn or damaged.  
4. Replace with a pre-wound spool, or re-  
place line using a 25 feet (8 meters)  
length of 0.080 inch (2 mm) diameter line.  
WARNING: Never use wire, rope,  
string, etc., which can break off and becomea  
dangerous missile.  
9. Place the spool in the cover as shown  
below.  
15  
 
REPLACING THE TRIMMER HEAD  
1. Hold the dust cup with a wrench to keep  
the shaft from turning while removing and  
installing trimmer head.  
Dust
2. Remove trimmer head by turning counter-  
clockwise (looking from bottom of unit).  
3. Thread replacement trimmer head onto the  
shaft by turning clockwise. Only tighten  
hand tight!  
10. Insert the ends of the lines through exit  
holes in the sides of the cover.  
Line exit hole  
CARBURETOR IDLE SPEED  
ADJUSTMENT  
WARNING: Keep others away when  
making idle speed adjustments. The trimmer  
head or any optional attachment will be spin-  
ning duringmost of this procedure. Wear your  
protective equipment and observe all safety  
precautions. After making adjustments, the  
trimmer head or any optional attachment  
must not move/spin at idle speed.  
ver  
11. Reinstall the spool and cover onto the  
trimmer head. Push untilcover snaps into  
place.  
The carburetor has been carefully set at the  
factory. Adjustments may benecessary if you  
notice any of the following conditions:  
S Engine will not idle when the throttle is  
released.  
S The trimmer head or any optional  
attachment moves/spins at idle.  
Make adjustments with the unit supported so  
the cutting attachment is off the ground and  
will not make contact with any object. Hold  
the unit by hand while running and making ad-  
justments. Keep all parts of your body away  
from the cutting attachment and muffler.  
To adjust idle speed:  
Allow engine to idle. Adjust speed until engine  
runs without trimmer head or any optional at-  
tachment moving or spinning (idle too fast) or  
engine stalling (idle speed too slow).  
S Turn idle speed screw clockwise to  
increase engine speed if engine stalls or  
dies.  
S Turn idle speed screw counterclockwise to  
decrease engine speed if trimmer head or  
any optional attachment moves or spins at  
idle.  
WARNING: Recheck the idle speed  
after each adjustment. The trimmer head or  
any optional attachment must not move or  
spin at idle speed toavoid serious injury tothe  
operator or others.  
16  
 
If you require further assistanceor are unsure  
about performing this procedure, contact an  
authorized  
service  
dealer  
or  
call  
1--800--554--6723.  
STORAGE  
HELPFUL TIP  
WARNING: Perform the following  
steps after each use:  
During storage of your gas/  
oil mixture, the oil will sepa-  
rate from the gas.  
S Allow engine to cool before storing or trans-  
porting.  
We recommend that you  
shake the gas can weekly  
to insure proper blending of  
the gas and oil.  
S Store unit and fuel in a well ventilated area  
where fuel vapors cannot reach sparks or  
open flames from water heaters, electric  
motors or switches, furnaces, etc.  
S Store unit with all guards in place. Position  
unit so that any sharp object cannot acci-  
dentally cause injury.  
ENGINE  
S Remove spark plug and pour 1 teaspoon of  
40:1, 2-cycle engine oil (air cooled) through  
the spark plug opening. Slowly pull the  
starter rope 8 to 10 times to distribute oil.  
S Replace spark plug with new one of recom-  
mended type and heat range.  
S Store unit and fuel well out of the reach of  
children.  
SEASONAL STORAGE  
Prepare unit for storage at end of season or if  
it will not be used for 30 days or more.  
If your unit is to be stored for a period of time:  
S Clean the entire unit before lengthy  
storage.  
S Clean air filter.  
S Check entire unit for loose screws, nuts,  
and bolts. Replace any damaged, broken,  
or worn parts.  
S At the beginning of the next season, use  
only fresh fuel having the proper gasolineto  
oil ratio.  
S Store in a clean dry area.  
S Lightly oil external metal surfaces.  
FUEL SYSTEM  
Under FUELING ENGINE in the OPERA-  
TION section of this manual, see messagela-  
beled IMPORTANT regarding the use of ga-  
sohol in your engine.  
OTHER  
S Do not store gasoline from one season to  
another.  
S Replace your gasoline can if it starts to rust.  
Fuel stabilizer is an acceptable alternative in  
minimizing the formation of fuel gum deposits  
during storage. Add stabilizer to the gasoline  
in the fuel tank or fuel storage container. Fol-  
low the mix instructions found on stabilizer  
container. Run engine at least 5 minutes after  
adding stabilizer.  
17  
 
TROUBLESHOOTING TABLE  
WARNING: Always stop unit and disconnect spark plug before performing all of the  
recommended remedies below except remedies that require operation of the unit.  
TROUBLE  
CAUSE  
REMEDY  
Engine will not  
start.  
1. Engine flooded.  
1. See “Starting a Flooded Engine” in  
Operation Section.  
2. Fuel tank empty.  
3. Spark plug not firing.  
4. Fuel not reaching  
carburetor.  
2. Fill tank with correct fuel mixture.  
3. Install new spark plug.  
4. Check for dirty fuel filter; replace.  
Check for kinked or split fuel line;  
repair or replace.  
5. Carburetor requires  
adjustment.  
5. Contact an authorized service dealer.  
Engine will  
not idle  
properly.  
1. Carburetor requires  
adjustment.  
1. See “Carburetor Idle Speed Adjustment”  
in Service and Adjustments Section.  
2. Crankshaft seals worn. 2. Contact an authorized service dealer.  
3. Compression low.  
3. Contact an authorized service dealer.  
1. Air filter dirty.  
1. Clean or replace air filter.  
2. Clean or replace plug  
and regap.  
Engine will not  
accelerate,  
lacks power,  
or dies under  
a load.  
2. Spark plug fouled.  
3. Carburetor requires  
adjustment.  
4. Carbon build-up on  
muffler outlet screen.  
5. Compression low.  
3. Contact an authorized service dealer.  
4. Contact an authorized service dealer.  
5. Contact an authorized service dealer.  
Engine  
1. Fuel mixture incorrect. 1. Empty fuel tank and refill with  
correct fuel mixture.  
smokes  
excessively.  
2. Air filter dirty.  
3. Carburetor requires  
adjustment.  
2. Clean or replace air filter.  
3. Contact an authorized service dealer.  
1. Fuel mixture incorrect.  
1. See “Fueling Engine” in Operation  
section.  
Engine runs  
hot.  
2. Spark plug incorrect.  
3. Carburetor requires  
adjustment.  
4. Carbon build-up on  
muffler outlet screen.  
2. Replace with correct spark plug.  
3. Contact an authorized service dealer.  
4. Contact an authorized service dealer.  
18  
 
LIMITED WARRANTY  
McCulloch, a division of Husqvarna Consumer  
In Canada, contact:  
Outdoor Products N.A., Inc., warrants to the  
original consumer purchaser that each new  
McCulloch brand gasoline tool or attachment is  
free from defects in material and workmanship  
and agrees to repair or replace under this war-  
ranty any defective gasoline product or attach-  
ment as follows from the original date of pur-  
chase.  
McCulloch  
850 Matheson Blvd. West  
Mississauga, Ontario L5V 0B4  
Giving the model number, serial number and  
date of purchase of your product and the name  
and address of the authorized dealer from  
whom it was purchased.  
THIS WARRANTY GIVES YOU SPECIFIC  
LEGAL RIGHTS, AND YOU MAY HAVE OTH-  
ER RIGHTS WHICH VARY FROM STATE TO  
STATE.  
NO CLAIMS FOR CONSEQUENTIAL OR  
OTHER DAMAGES WILL BE ALLOWED,  
AND THERE ARE NO OTHER EXPRESS  
WARRANTIES EXCEPT THOSE EX-  
PRESSLY STIPULATED HEREIN.  
SOME STATES DO NOT ALLOW LIMITA-  
TIONS ON HOW LONG AN IMPLIED WAR-  
RANTY LASTS OR THE EXCLUSION OR  
LIMITATIONS OF INCIDENTAL OR CONSE-  
QUENTIAL DAMAGES, SO THE ABOVE LIM-  
ITATIONS OR EXCLUSION MAY NOT APPLY  
TO YOU.  
This is a limited warranty within the meaning of  
that term as defined in the Magnuson--Moss Act  
of 1975.  
2 YEARS - Parts and Labor, when used for  
household purposes.  
90 DAYS - Parts and Labor, when used for  
commercial, professional, or income producing  
purposes.  
30 DAYS - Parts and Labor, if used for rental  
purposes.  
This warranty is not transferable and does not  
cover damage or liability caused by improper  
handling, improper maintenance or alteration, or  
the use of accessories and/or attachments not  
specifically recommended by McCulloch for  
this tool. This warranty does not cover tune--up,  
spark plugs, filters, starter ropes, cutting line, or  
rotating head parts that will wear and require re-  
placement with reasonable use during the war-  
ranty period. This warranty does not cover pre--  
delivery setup or normal adjustments explained  
in the instruction manual. This warranty does  
not cover transportation costs.  
The policy of McCulloch is to continuously  
improve its products. Therefore, McCulloch  
reserves the right to change, modify, or dis-  
continue models, designs, specifications,  
and accessories of all products at any time  
without notice or obligation to any purchaser.  
In the event you have a claim under this warran-  
ty, you must return the product to an authorized  
service dealer.  
Should you have any unanswered questions  
concerning this warranty, please contact:  
McCulloch, a division of Husqvarna  
Consumer Outdoor Products N.A., Inc.  
9335 Harris Corners  
Charlotte, NC 28269  
1--800--554--6723  
U.S. EPA/CALIFORNIA/ENVIRONMENT CANADA  
EMISSION CONTROL WARRANTY STATEMENT  
YOUR WARRANTY RIGHTS AND OB-  
LIGATIONS: The U.S. Environmental  
Protection Agency, California Air Resources  
Board, Environment Canada and McCulloch  
are pleased to explain the emissions control  
system warranty on your year 2010 and later  
small off--road engine. In California, all small off--  
road engines must be designed, built, and  
equipped to meet the State’s stringent anti--  
smogstandards. McCullochmust warrant the  
emission control system on your small off--  
road engine for the periods of time listed be-  
low provided there has been no abuse, ne-  
glect, or improper maintenance of your small  
off--road engine. Your emission control system  
includes parts such as the carburetor, the igni-  
tion system and the fuel tank. Where a warrant-  
able condition exists, McCulloch will repair  
your small off--road engine at no cost to you.  
Expenses covered under warranty include  
diagnosis, parts and labor.  
MANUFACTURER’S WARRANTY COV-  
ERAGE: If any emissions related part on your  
engine (as listed under Emissions Control  
Warranty Parts List) is defective or a defect in  
the materials or workmanship of the engine  
causes the failure of such an emission related  
part, the part will be repaired or replaced by  
McCulloch. OWNER’S WARRANTY RE-  
SPONSIBILITIES: As the small off--road en-  
gine owner, you are responsible for the per-  
formance of the required maintenance listed  
in your instruction manual. McCulloch recom-  
mends that you retain all receipts covering  
maintenance on your small off--road engine,  
but McCulloch cannot deny warranty solely  
for the lack of receipts or for your failure to en-  
sure the performance of all scheduled main-  
tenance. As the small off--road engine owner,  
you should be aware that McCulloch may  
deny you warranty coverage if your small off--  
road engine or a part of it has failed due to  
19  
 
abuse, neglect, improper maintenance, un-  
approved modifications, or the use of parts  
not made or approved by the original equip-  
ment manufacturer. You are responsible for  
presenting your small off--road engine to an  
McCulloch authorized repair center as soon as  
a problem exists. Warranty repairs should be  
completed in a reasonable amount of time, not  
to exceed 30 days. If you have any questions  
regarding your warranty rights and responsi-  
bilities, you should contact your nearest autho-  
rized service center, call McCulloch at  
1--800--554--6723, or send e-mail correspon-  
the determination that a warranted part is de-  
fective if the diagnostic work is performed at  
an approved McCulloch servicing center.  
CONSEQUENTIAL DAMAGES: McCulloch  
may be liable for damages to other engine  
components caused by the failure of a war-  
ranted part still under warranty. WHAT IS  
NOT COVERED: All failures caused by  
abuse, neglect, or improper maintenance are  
not covered. ADD -ON OR MODIFIED  
PARTS: The use of add--on or modified parts  
can be grounds for disallowing a warranty  
claim. McCulloch is not liable to cover failures  
of warranted parts caused by the use of add--  
on or modified parts. HOW TO FILE A  
CLAIM: If you have any questions regarding  
your warranty rights and responsibilities, you  
should contact your nearest authorized service  
center, call McCulloch at 1--800--554--6723, or  
send e-mail correspondence to emission.  
warranty@HCOP--emission.com. WHERE  
TO GET WARRANTY SERVICE: Warranty  
services or repairs shall be provided at all  
dence  
to  
emission.warranty@HCOP--  
emission.com. WARRANTY COMMENCE-  
MENT DATE: The warranty period begins on  
the date the small off--road engine is pur-  
chased. LENGTH OF COVERAGE: This  
warranty shall be for a period of two years  
from the initial date of purchase, or until the  
end of the product warranty (whichever is lon-  
ger). WHAT IS COVERED: REPAIR OR RE-  
PLACEMENT OF PARTS. Repair or re-  
placement of any warranted part will be  
performed at no charge to the owner at an ap-  
proved McCulloch servicing center. If you  
have any questions regarding your warranty  
rights and responsibilities, you shouldcontact  
your nearest authorized service center, call  
McCulloch at 1--800--554--6723, or send  
e-mail correspondence to emission.warranty  
@HCOP--emission.com. WARRANTY PE-  
RIOD: Any warranted part which is not  
scheduled for replacement as required main-  
tenance, or which is scheduled only for regu-  
lar inspection to the effect of “repair or replace  
as necessary” shall be warranted for 2 years.  
Any warranted part which is scheduled for re-  
placement as required maintenance shall be  
warranted for the period of time up to the first  
scheduled replacement point for that part.  
DIAGNOSIS: The owner shall not be  
charged for diagnostic labor which leads to  
McCulloch  
service  
centers.  
Call:  
1--800--554--6723 or send e-mail correspond-  
ence to emission.warranty@HCOP--emission.  
com. MAINTENANCE, REPLACEMENT  
AND REPAIR OF EMISSION RELATED  
PARTS: Any McCulloch approved replace-  
ment part usedinthe performanceof any war-  
ranty maintenance or repair on emission re-  
lated parts will be provided without charge to  
the owner if the part is under warranty. EMIS-  
SION CONTROL WARRANTY PARTS  
LIST: Carburetor, air filter (covered up to main-  
tenance schedule), ignition system: spark plug  
(covered up to maintenance schedule), ignition  
module, muffler including catalyst (if equipped),  
fuel tank. MAINTENANCE STATEMENT:  
The owner is responsible for the performance  
of all required maintenance as defined in the  
instruction manual.  
The information on the product label indicates which standard your engine is certified.  
Example: (Year) EPA and/or CALIFORNIA.  
This engine is certified to be emissions compliant for the following use:  
Moderate (50 hours)  
Intermediate (125 hours)  
Extended (300 hours)  
20  
 

Kyocera Printer FS 1900 User Manual
Land Pride Brush Cutter RCMB6010 User Manual
Land Pride Spreader 15 Series 48 72 User Manual
LG Electronics Projector RD JT31 800X600 SVGA User Manual
Life Fitness Bicycle LC 5000 User Manual
Little Wonder Chipper 8221 8271 User Manual
Makita Cordless Saw 15026DWA User Manual
Makita Cordless Saw JR14ODWA User Manual
Mamp;S Systems Portable Speaker MNCX User Manual
Microsoft Frozen Dessert Maker DHA025600 User Manual